Looking for a Ciizen Cincom F-Series cnc program

[jdcowles]

Hi im looking for a few sample programs for a Citizen Cincom F-12 or an F-25

Similar Threads:

• Need Help!- Loading a Program in Citizen L20 Series VII
• Need Help!- Program manual required for Series 21i-m
• Need Help!- Series 5 Lathe program
• copy program on fanuc series O or OT
• Series I with Heidenhain 155 Won't run program

[not_in_use]

I run an old (1984) Citizen F-20, if that'll help. Twin turret single spindle, live tooling.

[jdcowles]

Yes that would help

[not_in_use]

Ok. I'll pick a couple and send them to you Monday. I'll try and comment them out as best I can. I don't know about your controller but ours won't allow man-readable comments.

[jdcowles]

Thank you

[not_in_use]

Good morning JD. Here's the code for a simple aluminum tube we make on our F-20:

%
O0200
M52 (CHECKS TO SEE IF COOLANT ON)
G20 G97
G69
M7 (OPEN CHUCK)
G04 U0.5
G98 G1 W-0.759 F100.0 (PULL PART OUT)
G50 X0.0 Z-0.010 T0 (RESET ZERO TO -0.010)
M6 (CLOSE CHUCK)
G04 U0.5
G69 (UPPER TURRET)
G0 X-2.000 Z-0.100 T0 (UPPER TURRENT INDEX POSITION)
(CALL UP TOOL 12)
G99 T1200 S3000 M3
(T12 LOADS THE OFFSET FOR TOOL 12)
G0 X0.400 Z0.0 T12
G1 X0.000 F0.007
G0 Z-0.100
G69
G0 X-2.000 Z-0.100 T0
M1
(CALL UP TOOL 13)
(90 DEG SPOT DRILL)
T1300 S3000 M3
G0 X0.000 Z-0.100 T13
G1 Z0.110 F0.004
G0 Z-0.100
G69
G0 X-2.000 Z-0.100 T0
M1
(CALL UP TOOL 14)
(0.218 DRILL)
T1400 S3000 M3
G0 X0.000 Z-0.100 T14
G1 Z0.400 F0.004
G0 Z-0.1
Z0.380
G1 Z0.600
G0 Z-0.1
Z 0.580
G1 Z0.725
G0 Z-0.1
Z0.715
G1 Z0.775
G0 Z-0.1
G68 (UPPER TURRET)
G0 X8.500 Z-0.100 T0 (UPPER TURRET INDEX POSITION)
M1
(TOOL 24, BORING BAR)
T2400 S3000 M3
G0 X0.2243 Z-0.100 T24
G1 Z0.715 F0.004
X0.215
G0 Z-0.100
G69 (LOWER TURRET)
G0 X-2.000 Z-0.100 T0 (LOWER TURRET INDEX POSITION)
M1
(TOOL 12, TURN O.D.)
T1200 S3000 M3
G0 X0.400 Z0.000 T12
G1 X0.200 F0.005
G0 Z-0.050
X0.2854
G1 Z0.000
X0.3143 Z0.014 F0.0015
Z0.750 F0.007
X0.400
G68 (UPPER TURRET)
G0 X8.500 Z-0.100 T0 (UPPER TURRENT INDEX POSITION)
M1
(TOOL 23, PART OFF TOOL)
T2300 S3000 M3
G0 X0.400 Z0.749 T23
M32 (PARTS CATCHER OUT)
G4 U1.50
G1 X0.280 F0.004
G0 X0.350
Z0.740
G1 X0.3143
X0.2963 Z0.749 F0.0015
X0.200 F0.002
X-0.100 F0.003
M33 (PARTS CATCHER BACK)
G69
G0 G28 U0.0 W0.0
G50 X0.0 Z0.0 T0 M5
M2
%

Hope it helps. I'll answer any questions I can. Good luck!

-aj

[jdcowles]

Thanks for the program, it helps a lot. there's a machine shop I sometimes work part time hours at has an F12 and F25 and my full time job has has lathes and mills. I'm hoping to get my programing skills up to par.

[Plastomach]

Hello.. We are looking for parameters of Citizen L20 5-axis CNC Swiss Sliding Head Machine with Mitsubishi Medlas 300 control from 1997.
Let me know if anyone could provide us with it.. Thanks Regards