Zen Toolworks

Page 1 of 4 1234 LastLast
Threads 1 to 20 of 64

Forum: Zen Toolworks

Discuss Zen Toolworks products here!

  1. My CNC DREAM/NIGHTMARE!

    Started by Kobra000‎, 03-10-2011 06:24 AM
    9 Pages
    1 2 3 4 5 ... 9
    • Replies: 164
    • Views: 75,588
    04-14-2013, 07:24 AM Go to last post
  2. Where to start

    Started by jm82792‎, 08-24-2011 04:01 AM
    4 Pages
    1 2 3 4
    • Replies: 75
    • Views: 10,106
    12-12-2011, 06:11 PM Go to last post
  3. DIY aluminium and extrusion build BIG MACHINE

    Started by Usmanali‎, 12-20-2012 04:19 PM
    4 Pages
    1 2 3 4
    • Replies: 62
    • Views: 15,050
    01-08-2013, 12:24 PM Go to last post
  4. Drawer Slide CNC

    Started by jkarisny‎, 09-10-2011 12:16 PM
    3 Pages
    1 2 3
    • Replies: 46
    • Views: 47,494
    08-14-2014, 04:12 AM Go to last post
  5. 12"x12"x3" $400 Build

    Started by johnckovacs‎, 07-23-2012 07:24 PM
    2 Pages
    1 2
    • Replies: 36
    • Views: 24,668
    01-02-2016, 07:56 PM Go to last post
  6. CNC with $500 budget? Possible?

    Started by Gamble‎, 08-24-2011 03:45 PM
    2 Pages
    1 2
    except, maybe
    • Replies: 31
    • Views: 5,468
    09-02-2011, 08:37 AM Go to last post
  7. CNC spindle motor questions

    Started by nat45928‎, 08-20-2011 04:06 PM
    2 Pages
    1 2
    cnc spindle motor, down
    • Replies: 22
    • Views: 5,676
    08-26-2011, 11:45 PM Go to last post
  8. Nameless controller board from Ebay -specs.

    Started by podolskiy‎, 09-21-2012 01:17 AM
    2 Pages
    1 2
    • Replies: 21
    • Views: 3,277
    10-12-2012, 09:37 PM Go to last post
  9. Looking to get started with CNC...

    Started by alank2‎, 04-03-2012 06:43 PM
    cnc., not
    • Replies: 18
    • Views: 2,857
    04-05-2012, 08:50 PM Go to last post
  10. N00b Alert. So confused.

    Started by Gamble‎, 08-19-2011 10:43 AM
    everyone, not, onto, then
    • Replies: 17
    • Views: 2,868
    08-24-2011, 09:24 PM Go to last post
  11. Accuracy of milling PCBs for surface mount?

    Started by logik‎, 06-20-2009 02:21 AM
    • Replies: 15
    • Views: 25,057
    09-26-2010, 12:34 PM Go to last post
  12. What router for my diy cnc?

    Started by prodigy86‎, 06-04-2012 04:52 AM
    • Replies: 15
    • Views: 16,425
    06-12-2012, 05:55 AM Go to last post
  13. Recommended Feed Rates for Nema23 Steppers??

    Started by AssassinXCV‎, 03-19-2011 01:42 AM
    000rpm
    • Replies: 14
    • Views: 5,796
    03-20-2011, 10:36 PM Go to last post
  14. Help with this router bit

    Started by karandex‎, 03-29-2011 02:54 AM
    • Replies: 14
    • Views: 2,096
    03-30-2011, 12:10 AM Go to last post
  15. Would this router work?

    Started by ieatfish‎, 04-11-2011 02:37 PM
    • Replies: 11
    • Views: 1,714
    04-14-2011, 05:38 PM Go to last post
  16. For about $2000 what are different CNC kit options?

    Started by armanm‎, 11-09-2012 05:15 AM
    • Replies: 11
    • Views: 3,279
    11-11-2012, 04:12 PM Go to last post
  17. New CNC Build with questions

    Started by nat45928‎, 08-08-2011 06:20 PM
    far
    • Replies: 10
    • Views: 2,412
    06-27-2012, 06:34 PM Go to last post
  18. Unhappy 7 by 7 Dropping pulses or ?

    Started by EWhite‎, 01-17-2014 05:42 PM
    mos, say, then
    • Replies: 9
    • Views: 4,823
    03-27-2015, 05:03 PM Go to last post
  19. 24v PSU - low DC voltage?

    Started by SpyderHelix‎, 05-26-2012 11:36 PM
    electronics kit, next
    • Replies: 8
    • Views: 1,343
    05-30-2012, 12:38 AM Go to last post
  20. Items I need to buy not included in Zenbot 4848 kit?

    Started by 007lab‎, 01-20-2015 05:24 PM
    • Replies: 8
    • Views: 8,679
    02-16-2015, 04:40 PM Go to last post

Page 1 of 4 1234 LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 3 users browsing this forum. (0 members & 3 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands