Zen Toolworks

Page 1 of 4 1234 LastLast
Threads 1 to 20 of 64

Forum: Zen Toolworks

Discuss Zen Toolworks products here!

  1. Items I need to buy not included in Zenbot 4848 kit?

    Started by 007lab‎, 01-20-2015 05:24 PM
    • Replies: 8
    • Views: 8,679
    02-16-2015, 04:40 PM Go to last post
  2. Looking to get started with CNC...

    Started by alank2‎, 04-03-2012 06:43 PM
    cnc., not
    • Replies: 18
    • Views: 2,857
    04-05-2012, 08:50 PM Go to last post
  3. For about $2000 what are different CNC kit options?

    Started by armanm‎, 11-09-2012 05:15 AM
    • Replies: 11
    • Views: 3,279
    11-11-2012, 04:12 PM Go to last post
  4. Recommended Feed Rates for Nema23 Steppers??

    Started by AssassinXCV‎, 03-19-2011 01:42 AM
    000rpm
    • Replies: 14
    • Views: 5,796
    03-20-2011, 10:36 PM Go to last post
  5. CNC from CNC???

    Started by astainless‎, 01-30-2010 01:18 AM
    another, everyone, except
    • Replies: 6
    • Views: 1,968
    02-02-2010, 03:56 AM Go to last post
  6. New 2.1 build starting

    Started by Bigdog_1002‎, 06-13-2013 01:24 PM
    • Replies: 3
    • Views: 1,852
    06-15-2013, 01:07 AM Go to last post
  7. Student looking for Circuit board routing CNC

    Started by Bonz099‎, 09-17-2010 10:18 AM
    • Replies: 5
    • Views: 3,774
    09-20-2010, 04:19 AM Go to last post
    • Replies: 0
    • Views: 3,815
    11-15-2014, 11:07 AM Go to last post
  8. Question about zen tool works f8

    Started by Dr.Laser676‎, 05-26-2015 12:29 AM
    question, frame, tool, works, zen
    • Replies: 0
    • Views: 3,762
    05-26-2015, 12:29 AM Go to last post
  9. Stepper does not turn

    Started by dvdnhm‎, 07-26-2014 12:07 AM
    • Replies: 4
    • Views: 3,932
    07-28-2014, 05:28 AM Go to last post
  10. Standard Zen Lead Screw size/specs?

    Started by eekflyer‎, 03-03-2021 09:05 PM
    lead, screw, specification, standard, zen
    • Replies: 2
    • Views: 2,048
    03-03-2021, 11:33 PM Go to last post
  11. desktop size CNC (is there any open source design?)

    Started by error404‎, 12-28-2010 12:18 PM
    • Replies: 7
    • Views: 11,390
    02-22-2011, 03:59 PM Go to last post
  12. Unhappy 7 by 7 Dropping pulses or ?

    Started by EWhite‎, 01-17-2014 05:42 PM
    mos, say, then
    • Replies: 9
    • Views: 4,822
    03-27-2015, 05:03 PM Go to last post
  13. Just got my Zenbot 4896 - Mach3 config file needed

    Started by FelixK‎, 05-08-2018 11:35 AM
    file, mach3, mach3 config file 4896, zenbot, zenbot 4896
    • Replies: 4
    • Views: 6,576
    05-01-2021, 06:27 PM Go to last post
  14. Zen spindle only runs in pulses

    Started by flaplante‎, 07-10-2017 01:38 PM
    delay, power, problem, spindle, zen
    • Replies: 1
    • Views: 6,516
    07-18-2017, 10:40 AM Go to last post
  15. Arduino Hookup

    Started by fretman_2‎, 07-19-2016 04:41 PM
    connected, enable, hookup, left, noticed
    • Replies: 1
    • Views: 4,557
    07-21-2016, 06:03 PM Go to last post
  16. N00b Alert. So confused.

    Started by Gamble‎, 08-19-2011 10:43 AM
    everyone, not, onto, then
    • Replies: 17
    • Views: 2,868
    08-24-2011, 09:24 PM Go to last post
  17. TB6560 are they all the same?

    Started by Gamble‎, 08-24-2011 02:01 PM
    sub
    • Replies: 0
    • Views: 1,353
    08-24-2011, 02:01 PM Go to last post
  18. CNC with $500 budget? Possible?

    Started by Gamble‎, 08-24-2011 03:45 PM
    2 Pages
    1 2
    except, maybe
    • Replies: 31
    • Views: 5,468
    09-02-2011, 08:37 AM Go to last post
  19. Ordered Zen Toolworks 12" - What else do I need?

    Started by gjbloom‎, 05-05-2010 06:45 PM
    next
    • Replies: 3
    • Views: 3,547
    06-03-2010, 09:44 AM Go to last post

Page 1 of 4 1234 LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 4 users browsing this forum. (0 members & 4 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands