Zen Toolworks

Page 1 of 4 1234 LastLast
Threads 1 to 20 of 63

Forum: Zen Toolworks

Discuss Zen Toolworks products here!

  1. Just got my Zenbot 4896 - Mach3 config file needed

    Started by FelixK‎, 05-08-2018 12:35 PM
    file, mach3, mach3 config file 4896, zenbot, zenbot 4896
    • Replies: 4
    • Views: 3,130
    05-01-2021, 07:27 PM Go to last post
  2. Standard Zen Lead Screw size/specs?

    Started by eekflyer‎, 03-03-2021 10:05 PM
    lead, screw, specification, standard, zen
    • Replies: 2
    • Views: 665
    03-04-2021, 12:33 AM Go to last post
    • Replies: 2
    • Views: 3,385
    03-04-2019, 10:58 PM Go to last post
  3. Zen spindle only runs in pulses

    Started by flaplante‎, 07-10-2017 02:38 PM
    delay, power, problem, spindle, zen
    • Replies: 1
    • Views: 3,196
    07-18-2017, 11:40 AM Go to last post
  4. stepper motor driver amps

    Started by oldcoalminer‎, 04-09-2017 12:28 AM
    4amps, 5.6amps, amps, driver, rms
    • Replies: 0
    • Views: 2,040
    04-09-2017, 12:28 AM Go to last post
  5. motor tuning

    Started by Rajudh‎, 12-16-2016 11:24 AM
    board, cnc, micro, motor, stepping
    • Replies: 0
    • Views: 2,116
    12-16-2016, 11:24 AM Go to last post
  6. Arduino Hookup

    Started by fretman_2‎, 07-19-2016 05:41 PM
    connected, enable, hookup, left, noticed
    • Replies: 1
    • Views: 2,219
    07-21-2016, 07:03 PM Go to last post
  7. Driver fuse

    Started by kjking‎, 05-15-2016 12:35 AM
    • Replies: 0
    • Views: 2,310
    05-15-2016, 12:35 AM Go to last post
  8. 12"x12"x3" $400 Build

    Started by johnckovacs‎, 07-23-2012 08:24 PM
    2 Pages
    1 2
    • Replies: 36
    • Views: 20,413
    01-02-2016, 08:56 PM Go to last post
  9. zen toolworks cnc with ramps v1.4

    Started by journeyp‎, 10-06-2015 12:44 AM
    axis, cnc, direction, pins, ramps
    • Replies: 1
    • Views: 2,799
    10-07-2015, 03:42 PM Go to last post
  10. Question about zen tool works f8

    Started by Dr.Laser676‎, 05-26-2015 01:29 AM
    question, frame, tool, works, zen
    • Replies: 0
    • Views: 2,169
    05-26-2015, 01:29 AM Go to last post
  11. Unhappy 7 by 7 Dropping pulses or ?

    Started by EWhite‎, 01-17-2014 06:42 PM
    mos, say, then
    • Replies: 9
    • Views: 3,257
    03-27-2015, 06:03 PM Go to last post
  12. Items I need to buy not included in Zenbot 4848 kit?

    Started by 007lab‎, 01-20-2015 06:24 PM
    • Replies: 8
    • Views: 6,854
    02-16-2015, 05:40 PM Go to last post
    • Replies: 3
    • Views: 2,252
    01-09-2015, 06:02 PM Go to last post
  13. question about upgradea

    Started by manakawari‎, 01-01-2015 09:08 PM
    • Replies: 1
    • Views: 2,090
    01-02-2015, 03:19 PM Go to last post
    • Replies: 0
    • Views: 2,208
    11-15-2014, 12:07 PM Go to last post
  14. Drawer Slide CNC

    Started by jkarisny‎, 09-10-2011 01:16 PM
    3 Pages
    1 2 3
    • Replies: 46
    • Views: 41,088
    08-14-2014, 05:12 AM Go to last post
  15. Stepper does not turn

    Started by dvdnhm‎, 07-26-2014 01:07 AM
    • Replies: 4
    • Views: 2,382
    07-28-2014, 06:28 AM Go to last post
  16. Newbie with problems.

    Started by tayda‎, 06-02-2014 06:29 PM
    cnc.
    • Replies: 0
    • Views: 2,240
    06-02-2014, 06:29 PM Go to last post
  17. Burned Out Dremel 4000

    Started by mjj‎, 05-22-2014 01:24 AM
    5.5mm, another, cor, down, except, its, maybe, mos, since, then, took, within
    • Replies: 5
    • Views: 4,290
    05-23-2014, 04:52 PM Go to last post

Page 1 of 4 1234 LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 1 users browsing this forum. (0 members & 1 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands