Xylotex

Page 1 of 15 123411 ... LastLast
Threads 1 to 20 of 288

Forum: Xylotex

Discuss all Xylotex drivers here!

  1. captzman193

    Started by captzman193‎, 10-30-2020 07:28 PM
    cnc, lights, low, switches, top
    • Replies: 0
    • Views: 348
    10-30-2020, 07:28 PM Go to last post
    • Replies: 4
    • Views: 6,458
    12-09-2019, 09:21 PM Go to last post
  2. Need Help!- Stepper Motors

    Started by ironclad246‎, 03-10-2019 09:22 PM
    inches, mach3, motors, steps, tuning
    • Replies: 2
    • Views: 2,772
    03-11-2019, 08:27 PM Go to last post
  3. Need Help!- Stepper Motors

    Started by ironclad246‎, 03-10-2019 10:49 PM
    inches, mach3, motors, steps, tuning
    • Replies: 2
    • Views: 1,189
    03-11-2019, 11:29 AM Go to last post
  4. Need Help!- Xylotex controller

    Started by cnc Rookie‎, 06-21-2017 01:01 PM
    axis, mach, running, stepper, xylotex
    • Replies: 0
    • Views: 3,897
    06-21-2017, 01:01 PM Go to last post
  5. Need Help!- Xylotex Board quit working !

    Started by kel1‎, 03-28-2009 03:02 PM
    away, down, took
    • Replies: 2
    • Views: 7,552
    11-10-2016, 01:30 AM Go to last post
  6. Xylotex 4 axis with a different controller for Z

    Started by windy46‎, 03-03-2016 08:19 AM
    • Replies: 7
    • Views: 4,184
    03-03-2016, 02:58 PM Go to last post
  7. Need Help!- Xylotex board used in old CNC Shark controller.

    Started by dreiii‎, 04-25-2015 05:47 PM
    board, cnc, laser, turn, unit
    • Replies: 1
    • Views: 5,917
    04-25-2015, 10:52 PM Go to last post
  8. Xylotex 4 axis control box for sale.

    Started by hacker7‎, 09-29-2014 12:44 AM
    170, 4 axis, 4x4, 649, axis, box, cnc, cnc control, con, control, control box, ebay, for sale, issue, link, router, router table, sale, table, time, wrong, xylotex
    • Replies: 1
    • Views: 5,744
    10-01-2014, 01:48 AM Go to last post
  9. Adding estop to Xylotex board

    Started by cgallery‎, 09-21-2014 11:46 PM
    cnc, cnc router, controller, delay, drive, e-stop, emergency stop, indicate, mach, mach3, manual, maybe, motion, next, parallel, parallel port, point, reset, router, said, screw, stepper, thinking, time, wired, xylotex
    • Replies: 2
    • Views: 2,871
    09-28-2014, 08:54 PM Go to last post
  10. Setting VRef on original Xylotex 3-axis board

    Started by cgallery‎, 09-20-2014 12:42 AM
    • Replies: 2
    • Views: 3,661
    09-20-2014, 10:55 PM Go to last post
  11. Xylotex 425 motors with gecko G540?

    Started by StuartC‎, 05-20-2014 08:35 AM
    • Replies: 3
    • Views: 3,553
    08-20-2014, 11:58 AM Go to last post
  12. Motor moves faster and farther in one direction

    Started by momojoey‎, 07-14-2014 08:35 PM
    away, far, then
    • Replies: 0
    • Views: 2,647
    07-14-2014, 08:35 PM Go to last post
  13. New box and limit switches

    Started by clembrant‎, 03-31-2014 07:18 PM
    • Replies: 5
    • Views: 3,052
    04-11-2014, 08:11 AM Go to last post
  14. Need Help!- electronics help please

    Started by brent48‎, 03-25-2014 05:03 AM
    rewiring
    • Replies: 0
    • Views: 2,535
    03-25-2014, 05:03 AM Go to last post
  15. replacement power supply

    Started by bartniswonger‎, 10-16-2013 08:39 AM
    33%, down
    • Replies: 1
    • Views: 3,063
    10-18-2013, 10:23 AM Go to last post
  16. Single Axis Problem

    Started by Taflin‎, 09-11-2013 04:25 PM
    • Replies: 0
    • Views: 2,149
    09-11-2013, 04:25 PM Go to last post
    • Replies: 7
    • Views: 4,550
    07-28-2013, 12:42 AM Go to last post
  17. Xylotex boards for sale - need repair

    Started by sonosabi‎, 02-20-2013 09:55 AM
    • Replies: 0
    • Views: 3,912
    02-20-2013, 09:55 AM Go to last post
  18. Xylotex controllers any good vs gecko?

    Started by noobCNC‎, 10-29-2011 08:51 PM
    • Replies: 7
    • Views: 6,718
    07-21-2012, 04:52 AM Go to last post

Page 1 of 15 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 1 users browsing this forum. (0 members & 1 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands