Uncategorised WoodWorking Machines


Page 1 of 24 123411 ... LastLast
Threads 1 to 20 of 467

Forum: Uncategorised WoodWorking Machines

Uncategorised WoodWorking Machine Discussion here!

  1. Moved: Looking for advice on ball screw nut repair

    Started by MAHNKEN‎, 11-19-2021 12:31 PM
    •  
    •  
  2. Good design CNC router

    Started by Decieved‎, 03-27-2021 10:38 AM
    cnc, good, made, router, steel
    • Replies: 1
    • Views: 958
    10-30-2021, 11:45 PM Go to last post
  3. New to CNC. Q's about Brand, spoil board, spindle

    Started by Jussi720‎, 10-03-2021 09:37 AM
    cnc, link, machine, onefinity, spindle
    • Replies: 0
    • Views: 382
    10-03-2021, 09:37 AM Go to last post
  4. LHR TECHNOLOGIES aka carvewright over controlling

    Started by Shelby5041‎, 09-22-2021 10:55 PM
    machine, machines, owner, previous, software
    • Replies: 2
    • Views: 263
    09-23-2021, 05:42 PM Go to last post
  5. Carvewright / compucarve cnc retrofit?

    Started by Shelby5041‎, 09-20-2021 11:22 AM
    carvewright, cnc, motors, retrofit, servo
    • Replies: 1
    • Views: 256
    09-20-2021, 02:45 PM Go to last post
  6. Need Help!- Mach 4 conversion, Spindle only turns on, no speed control.

    Started by rudie7501‎, 09-04-2021 06:36 PM
    cnc, mach, setup, software, spindle
    • Replies: 3
    • Views: 376
    09-05-2021, 05:34 PM Go to last post
  7. OX CNC

    Started by mjadams61‎, 08-28-2021 03:53 PM
    cnc, kit, motors, purchase, stepper
    • Replies: 0
    • Views: 360
    08-28-2021, 03:53 PM Go to last post
  8. Need Help!- What CNC machine could cut this out?

    Started by Usman78639‎, 08-12-2021 05:06 PM
    2 Pages
    1 2
    • Replies: 20
    • Views: 944
    08-14-2021, 09:41 PM Go to last post
  9. Machine shuts down during a cut

    Started by Vernon1‎, 08-08-2021 04:37 PM
    button, cnc, cut, machine, stop
    • Replies: 7
    • Views: 545
    08-10-2021, 02:07 PM Go to last post
  10. Need Help!- Help with router config. settings

    Started by notselrach‎, 07-24-2021 01:24 AM
    config, relay, router, settings, switch
    • Replies: 1
    • Views: 629
    07-24-2021, 07:40 AM Go to last post
  11. Scaling up: What's out there?

    Started by Thunderskunk‎, 07-08-2021 01:50 PM
    bench, cnc, cut, drill, router
    • Replies: 0
    • Views: 491
    07-08-2021, 01:50 PM Go to last post
  12. PADE UNI 5

    Started by ndngarcez‎, 06-29-2021 07:36 PM
    bring, esey, pade, problem, uni
    • Replies: 0
    • Views: 330
    06-29-2021, 07:36 PM Go to last post
  13. CNC sounds like a sick moose

    Started by grantx‎, 06-19-2021 04:25 PM
    bad sound, cnc, noisy, resonance, vibration
    • Replies: 13
    • Views: 539
    06-20-2021, 11:57 AM Go to last post
  14. Need Help!- Rockler, Click N Carve, Bravoprodigy software installation disk lost

    Started by Harvey73‎, 10-06-2015 08:39 AM
    carve, click, disk, software, suite
    • Replies: 6
    • Views: 3,375
    05-16-2021, 02:15 PM Go to last post
  15. nuova progetti program

    Started by KamilF‎, 05-13-2021 04:29 PM
    • Replies: 0
    • Views: 255
    05-13-2021, 04:29 PM Go to last post
  16. warthog calibration

    Started by MAHNKEN‎, 05-06-2021 01:10 PM
    • Replies: 0
    • Views: 243
    05-06-2021, 01:10 PM Go to last post
  17. Moved: Need Help!- New user 3018 CNC problem

    Started by smart51‎, 04-26-2021 08:04 AM
    •  
    •  
  18. Moved: Need Help!- strange Y axis problem on Gerber CNC

    Started by Syx1977‎, 04-01-2021 03:57 AM
    •  
    •  
  19. Machine adding steps when milling

    Started by Pugman1‎, 03-24-2021 02:27 PM
    checked, cnc, cutting, machine, that’s
    • Replies: 0
    • Views: 568
    03-24-2021, 02:27 PM Go to last post
  20. Need Help!- Laguna IQ help, Z Axis ignores feedrates in Gcode?

    Started by suade907‎, 03-10-2021 08:58 PM
    a11e, control, gcode, laguna iq, richauto
    • Replies: 3
    • Views: 578
    03-24-2021, 12:56 AM Go to last post

Page 1 of 24 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 8 users browsing this forum. (0 members & 8 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands