Hitachi Seiki Service and Support!!!!!!!!1 - Page 4


Page 4 of 11 FirstFirst 1234567 ... LastLast
Results 61 to 80 of 208

Thread: Hitachi Seiki Service and Support!!!!!!!!1

  1. #61
    Banned yours_prabhat's Avatar
    Join Date
    Dec 2008
    Location
    India
    Posts
    239
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by cncrepairs View Post
    Dear All

    I have a hitachi machine and facing following problem ,can any one help me to get a soft copy of pc ladle. following are the details.

    Problem -- PLC DATA LOST ON HITACHI SEIKI HG500

    Service Required -- A Soft Copy of PC LADLE.( We have a
    communication software and cable for
    uploading

    Machine Details

    Model--- HG500

    CNC ---FANUC 15 MA

    SR No --HG50229

    PLC --- Hitachi Seiki make MICON 16 II

    Specifications--- Normal

    Ladle Program No---2741-A02T(Mentioned in the electrical diagram
    book)

    cncrepairs(cncepairs@rediffmail.com)
    i can send give your contact details .
    Regards
    Prabhat Mishra
    +91-9430737981
    prabhatmishra@mail.com



  2. #62
    Registered Hitachi_man's Avatar
    Join Date
    Nov 2004
    Location
    USA
    Posts
    36
    Downloads
    0
    Uploads
    0

    Default I'm back

    I would like to start by saying sorry to everyone for being away for so long, it was unavoidable.

    I am back and you can contact me on this site I will be checking it daily again. I am servicing machines again!! So hit me up

    thanks



  3. #63
    Registered
    Join Date
    Feb 2007
    Location
    MEXICO
    Posts
    17
    Downloads
    0
    Uploads
    0

    Default

    very good, hitachi man.
    can you help me with a cnc hitachi maccmatic 48v?.



  4. #64
    Registered
    Join Date
    Dec 2008
    Location
    usa
    Posts
    26
    Downloads
    0
    Uploads
    0

    Default hitachi lathe

    i have a hitachi seiki lathe from '99. I want override the door settings so i can machine with the door open. Is there any way to do this?

    Also, I have a bar puller and I want to be able to open the chuck, pull the bar out, and close the chuck while a program is running. Do I have to make any changes to the settings?

    Thanks.



  5. #65
    Registered
    Join Date
    May 2009
    Location
    Poland
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default

    Hello Josh,
    Unfortunately i am located in Poland, Europe and can't ask you to come over, so perhaps you can help me via e-mail.
    We have Hitachi-Seiki HT-15 with Seicos M II control
    The battery has been changed
    Currently we have :
    -battery alarm
    -5022,5031,5033 alarms
    -slbus table error

    No manuals of any kind available

    Any idea how to get rid of them??
    Regards, Andrew



  6. #66
    Registered
    Join Date
    May 2009
    Location
    Poland
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default

    Hello Josh,
    Unfortunately i am located in Poland, Europe and can't ask you to come over, so perhaps you can help me via e-mail.
    We have Hitachi-Seiki HT-15 with Seicos M II control
    The battery has been changed
    Currently we have :
    -battery alarm
    -5022,5031,5033 alarms
    -slbus table error

    No manuals of any kind available

    Any idea how to get rid of them??
    Regards, Andrew



  7. #67
    Registered
    Join Date
    Jun 2009
    Location
    China
    Posts
    2
    Downloads
    0
    Uploads
    0

    Smile VS50

    Hi Hitachi man,

    Good day!
    I have a HITACHI SEIKI VS 50 milling.(Fanuc 18M)
    But the SIMENS PLC(S7-200) is bad.
    Can you send me the ladder for Simens PLC .(Not PMC ladder)
    Then I can change a new one.



  8. #68
    Registered
    Join Date
    Jun 2009
    Location
    China
    Posts
    2
    Downloads
    0
    Uploads
    0

    Smile VS50

    Hi Hitachi man,

    Good day!
    I have a HITACHI SEIKI VS 50 milling.(Fanuc 18M)
    But the SIMENS PLC(S7-200) is bad.
    Can you send me the ladder for Simens PLC .(Not PMC ladder)
    Then I can change a new one.

    E-MAIL:CHARLES-LZF@HOTMAIL.COM



  9. #69
    Registered
    Join Date
    Dec 2008
    Location
    usa
    Posts
    26
    Downloads
    0
    Uploads
    0

    Default

    hi,

    i have a hitachi seiki ht40g with a seicos A10L. I bought it in 1999. I hit feed hold during a tool change. It gave me an alarm, and I couldn't reset it, so I powered off the machine. When I powered back on, the alarm is still there. I'm getting a turret index power off (2252) alarm. Any way I can reset the turret?

    thanks!



  10. #70
    Registered
    Join Date
    Dec 2008
    Location
    usa
    Posts
    26
    Downloads
    0
    Uploads
    0

    Default fixed turret butt...

    ok so i got the alarm to go away but now the tool numbers are off... if i call up tool 5, it gives me tool 8... how do i fix that?


    manoj



  11. #71
    Member
    Join Date
    Sep 2008
    Location
    Canada
    Posts
    138
    Downloads
    0
    Uploads
    0

    Default Hi Hitachi Man

    Quote Originally Posted by Hitachi_man View Post
    I would like to start by saying sorry to everyone for being away for so long, it was unavoidable.

    I am back and you can contact me on this site I will be checking it daily again. I am servicing machines again!! So hit me up

    thanks
    Could you tell me how to input data for Micron-8

    Regards



  12. #72
    Banned yours_prabhat's Avatar
    Join Date
    Dec 2008
    Location
    India
    Posts
    239
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by seawolf217 View Post
    ok so i got the alarm to go away but now the tool numbers are off... if i call up tool 5, it gives me tool 8... how do i fix that?


    manoj
    check the micro program correctly and if you have back up of Micro ATC programe please re load it in machine If the problem persist feel free to communicate me on prabhatmishra@mail.com or on +919430737981



  13. #73
    Registered
    Join Date
    Oct 2008
    Location
    LA
    Posts
    32
    Downloads
    0
    Uploads
    0

    Default

    Hi,

    When starting spindle by MDI at speed 500 rpm for boring soft jaws. Alarm No 520 appears saying "Spindle start impossible, Check door close, chuck close and center position".

    Door close LED is ON, both the chuck proximity switch also ON (LED ON) i cannot find location of center position LED or proximity switch.

    How to confirm about center position . Machine is Hitachi Seiki HT20SII .

    I have its programming manuals but no operation manual. An help in this regard will be highly appreciated.

    Regards,



  14. #74
    Registered
    Join Date
    Oct 2009
    Location
    Republica Dominicana
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default

    Hello> I'm from Dominican Republic
    I have a tri-turn model cnc 4NE-II-600,
    Series # NE-42346SC. FS-NC Fanuc 3TF.
    Well the point is that the machine gives me an error that is this low parity. I know how to delete it, and I also need the parameter.
    I thank you beforehand.
    Greetings. DUARTE VELEZ ..



  15. #75
    Registered
    Join Date
    Oct 2009
    Location
    Republica Dominicana
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default

    hola hitachi man
    tengo una hitachi seki 4ne-II-600 control fanuc FS 3TF
    y me da un error parity low. por favor como resorver el errror

    SALUDOS Y GRACIAS.
    Duarte Velez



  16. #76
    Member Dancy's Avatar
    Join Date
    Aug 2007
    Location
    usa
    Posts
    138
    Downloads
    0
    Uploads
    0

    Default Did the MIB get him?

    Has anyone heard from Josh aka Hitachi man since his last post in Sept? I would love to see some posts from him. I am looking for schematics for my VK45 mill. I want to add a 4th axis to it and need some help.

    Keshka



  17. #77
    Registered
    Join Date
    Jul 2009
    Location
    USA
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default HITACHI SEIKI VA-40 FANUC 6M CONTROL spindle drive

    I got a problem with a Hitachi VA-40 the Spindle drive and motor were checked by OESS and both of them checked good but every time try to stop the spindle with M05 it gives me an OCL LED alarm on the spindle drive....Any idea what this problem might be? please email me at robert@jrpm.com
    Thank You



  18. #78
    Member
    Join Date
    Sep 2008
    Location
    Canada
    Posts
    138
    Downloads
    0
    Uploads
    0

    Default About 4th Axis

    Quote Originally Posted by Dancy View Post
    Has anyone heard from Josh aka Hitachi man since his last post in Sept? I would love to see some posts from him. I am looking for schematics for my VK45 mill. I want to add a 4th axis to it and need some help.

    Keshka
    Pls PM for me your email



  19. #79
    Member
    Join Date
    Nov 2006
    Location
    USA
    Posts
    303
    Downloads
    0
    Uploads
    0

    Default

    I have tried several times to contact him. No go. I created another thread looking for reliable service contacts. There seems to be many machines still in service yet very little support. I have a Seicos III in a lathe and looking for all the contacts I can find...



  20. #80
    Member
    Join Date
    Sep 2008
    Location
    Canada
    Posts
    138
    Downloads
    0
    Uploads
    0

    Default Need help with Hitachi Seiki VM40

    Dear all

    I have Hitachi Seicos VM40 with controller is Micron 16 MII. Battery was dead so all data was lost. Dose anybody have all data for my machine. I'm willing to buy it

    Regards



Page 4 of 11 FirstFirst 1234567 ... LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Hitachi Seiki Service and Support!!!!!!!!1

Hitachi Seiki Service and Support!!!!!!!!1