Hitachi Seiki Service and Support!!!!!!!!1 - Page 14


Page 14 of 14 FirstFirst ... 411121314
Results 157 to 168 of 168

Thread: Hitachi Seiki Service and Support!!!!!!!!1

  1. #157
    Registered CyberCNC's Avatar
    Join Date
    Apr 2009
    Location
    USA
    Posts
    34
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Service and Support!!!!!!!!1

    Quote Originally Posted by Esteban_Juan View Post
    Dear Josh:


    I have many questions about a machining center Hitachi with the following characteristics :
    Machine: HITACHI SEIKI
    CONTROL: FANUC 6M Model B
    Type: MACC MATCH
    MFGNO: C22162-1
    1984-10

    Can you give us technical assistance?
    Best Regards

    my email is ejsejas@indesa.com.bo
    my name is Esteban Sejas
    whatsapp: +591-79014994
    Dear Sir,

    I do not believe this is an Hitachi Seiki machine tool. can you please supply Model and serial number if you are still looking for support.

    Jeffrey Kale

    General Manager

    [COLOR="#0000CD"]CYBER CNC MACHINERY SALES,INC.[/COLOR]
    [COLOR="#0000CD"][COLOR="#0000CD"]S86 W22400 Edgewood Avenue
    Big Bend, WI 53103
    Phone: (262) 662-1100[/COLOR][/COLOR]


  2. #158
    Registered
    Join Date
    Aug 2013
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default

    Hi John,
    Can you give me a call at 203-483-1420, I am having problems with a Hitachi Seiki HT 20SII.
    Bruce
    Mold Threads, Inc



  3. #159
    Registered Billet Carb's Avatar
    Join Date
    Feb 2014
    Posts
    30
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Service and Support!!!!!!!!1

    I am look for support for a Hitachi Seiki HC 400. If experienced with this machine , I can pay for support.
    The machine has a Fanuc 15 M controller .
    Recently it has developed an intermittent problem. It starts up normally, all normal lights lite, no alarms ,, but no axis move in handle or any other mode.
    Therefore I can not Auto Zero the machine. It just sits there looking like it should be running and not.
    I am sure someone has dealt with this other than me.
    Regards,
    John from dambest Carburetor
    845 473 1136



  4. #160
    Registered
    Join Date
    May 2011
    Location
    india
    Posts
    9
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Service and Support!!!!!!!!1

    Dear sir,
    I am baskaran from sharjah my machine hitachi 23s ii type machine continuous off ,how much month back up storage ,now time spindle bearing removing already one month finish



  5. #161
    Registered
    Join Date
    Apr 2011
    Location
    Romania
    Posts
    102
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Service and Support!!!!!!!!1

    Helllo guys i just got a Seiki Seicos my2 and i have some smalll problems . My machine had 5 axis some time ago . Some one stole the 4x5 axis from the machine and cut the wire . I have managed to get the wires out . started the machine and i need some how to get out the 4x5 axis from the software so i can work with the machine in 3 axis as i want . Did some one have made this modification ? Hitachi Seiki Service and Support!!!!!!!!1-image-16-12-16-06-56-1-aHitachi Seiki Service and Support!!!!!!!!1-image-16-12-16-06-56-jpeg i have fix the hard limit . I cant find in the manual how to get out the extra axis .



  6. #162
    Registered
    Join Date
    Feb 2016
    Location
    Viet Nam
    Posts
    17
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Service and Support!!!!!!!!1

    Hello,
    I have the machine hitachi seiki VK 55II with seico 10 control. and now I can't reset the alarm [742] Editing the program. Does any one know how to fix this alarm. I need your helps.

    Thank you!



  7. #163
    Registered
    Join Date
    Jun 2015
    Posts
    39
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Service and Support!!!!!!!!1

    Quote Originally Posted by riotmfg View Post
    Any idea where these thermal overloads are? I have looked everywhere, reset all breakers I could find but am still getting the AL-3 Thermal Alarm.

    I managed to clear the lube alarm by cleaning up the sensor in the lube reservoir. PLEASE help, I need to get this thing running.

    -Madison
    I dont usually do a necroposting, but in my case - all thermal overlaod alarms were due broken fan at the back of the control panel



  8. #164
    Member
    Join Date
    Sep 2009
    Location
    Macedonia
    Posts
    68
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Man

    Hi!

    We have a big problem on a machine HITACHI SEIKI VM40 with SEICOS M2 control, year 1988, SN No:40309,
    the machine was working just fine until the battery alarm appeared on the screen 033 BATTERY ALARM
    the both batteries were changed while the machine was powered off (unfortunately big mistake)
    on the screen we had:
    at first BUBBLE READ
    and then after a few seconds
    PC NOT READY
    SEICOS
    mark 2
    when we press NC/PC and then IINPUT the messages on the screen are:
    SUM CHECK ERROR SEQUENCER NOT READY
    BATTERY ALARM PLEASE CHANGE

    We found some procedure for overcoming this status on the machine
    the procedure that we conduct it is:

    1. Press F1(SEQUENCE) ->Press F2(DATASET) -> Press F4(TABLE) -> You will see “Constance Byte Table 1
    2. Type 0 0 (in the 1. 00) -> Press INPUT -> You will see Parameter Write Enable SW On ---------------
    3. Turn on WRITE ENABLE SW that is on MICON16-2 board in control panel
    4. Press F6(END). -> You will see Write Enable SW Off
    5. Turn off WRITE ENABLE SW
    6. Press F6(END) -> Press F1(SEQUENCE) ->Press F3(PROGRAM) -> You will see Parameter Write Enable SW On
    7. Turn on WRITE ENABLE SW that is on MICON16-2 board in control panel
    8. You will see top line of ladder automatically
    9. Press F2(ALTER) -> You will see ___(Cursor) on screen.
    10. Press F4(STORE) -> Press INPUT.
    11. Press F6(END) -> You will see Write Enable SW Off
    12. Turn off WRITE ENABLE SW
    13. Turn off NC power -> Turn on NC power

    After we did the procedure, we turn on the machine and we get Z80 CPU ALARM on the screen any suggestions how to continue from here?!?!

    We are asking a confirmation did we apply the right procedure?
    and after this we are assuming that the parameters should be loaded
    we have a backup of the original parameters,
    but if we need to load anything else please advise,

    If this is not the right procedure please let us know
    and point us for the right procedure in step by step if possible,

    We don't have any experience with this machine or this control so any suggestion is more than welcome,

    Thank you all in advance,

    Regards,



  9. #165
    sedi66's Avatar
    Join Date
    Jan 2018
    Location
    san luis potosi
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default

    i need electric drawing hitachi seiki va 45 fanuc 11m can you help me



  10. #166
    Registered
    Join Date
    Sep 2014
    Posts
    6
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by sedi66 View Post
    i need electric drawing hitachi seiki va 45 fanuc 11m can you help me
    Dear friends
    I need operation manual, wiring diagram, for a 5NE-1100 hitachi seiki lathe 1980 with fanuc 6T control
    thanks



  11. #167
    Member Florsita3's Avatar
    Join Date
    Feb 2019
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Seiki Service and Support!!!!!!!!1

    Quote Originally Posted by Hitachi_man View Post
    Hello all out there lost in the confusion of trying to find support for your Hitachi Seiki machines. I own a CNC Service Company in Wichita Kansas working on all brands of machines, but specializing in Hitachi Seiki. I currently have over 10 gig of info on Hitachi Seiki machines in my database from machine software to procedures and ELECTRICAL MANUALS!!!!! I have years of experience working with these machines, and until June of 04 I worked for Mori Seiki in LA as the Hitachi Seiki specialist. We DO travel, and my hourly rate for shop labor is only $75.00 per hour no matter what state your in. I also do phone support and provide procedures at $45.00 per hour 1 hour min....If you have a Hitachi Seiki machine, other machine models welcome also, call us and we will be happy to help!!! (cureing your headaches is free!!)

    You can contact us at 316-744-0549 just ask for Josh, aka Hitachi_man

    well be looking forward to hearing from you!!!
    HELLO
    I looking for DOCUMENTATION CS20/25 SEIKOS 21i TA (with motor and BETA DRIVE TURRET) with alarm 1020. Regards



  12. #168
    Member Dancy's Avatar
    Join Date
    Aug 2007
    Location
    usa
    Posts
    123
    Downloads
    0
    Uploads
    0

    Default Re: Hitachi Man

    vladimir, you have lost the ladder program for your mill. PM me and I will email instructions

    Keshka



Page 14 of 14 FirstFirst ... 411121314

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Hitachi Seiki Service and Support!!!!!!!!1

Hitachi Seiki Service and Support!!!!!!!!1

Hitachi Seiki Service and Support!!!!!!!!1