UHU Servo Controllers - Page 3

Page 3 of 5 FirstFirst 12345 LastLast
Threads 41 to 60 of 83

Forum: UHU Servo Controllers

Discuss UHU Servo Controllers here!

  1. ENCODER AMT102 PROBLEM

    Started by dfv‎, 04-10-2010 04:25 PM
    its, keep, not, then
    • Replies: 3
    • Views: 2,589
    04-10-2010, 08:26 PM Go to last post
  2. Does Anyone Have A Schematic of A UHU In Servie

    Started by bill south‎, 09-23-2009 06:07 AM
    • Replies: 4
    • Views: 2,746
    04-02-2010, 07:40 PM Go to last post
  3. High power UHU

    Started by bolttjza‎, 03-28-2010 11:13 PM
    not
    • Replies: 5
    • Views: 3,050
    03-31-2010, 10:45 PM Go to last post
  4. UHU programming cable

    Started by cncfreakcom‎, 03-22-2010 06:03 AM
    regards
    • Replies: 2
    • Views: 1,932
    03-22-2010, 04:45 PM Go to last post
  5. OLD UHU POSITION ERROR

    Started by dfv‎, 03-22-2010 09:50 AM
    next, not
    • Replies: 2
    • Views: 1,640
    03-22-2010, 01:16 PM Go to last post
  6. UHU Chip problems

    Started by mibo1112‎, 02-03-2010 06:12 AM
    next, not, said, then, took
    • Replies: 18
    • Views: 4,102
    02-18-2010, 06:53 PM Go to last post
  7. Exclamation Bidirectional Problem with UHU Board

    Started by jlobin‎, 02-01-2010 11:15 AM
    cause, not
    • Replies: 2
    • Views: 1,853
    02-04-2010, 03:16 AM Go to last post
  8. Unhappy Can not reset UHU Servo Controller

    Started by mibo1112‎, 01-14-2010 04:36 AM
    not, then, went
    • Replies: 9
    • Views: 2,698
    02-03-2010, 05:53 AM Go to last post
  9. Confusion on Old UHU encoder action

    Started by jlobin‎, 01-29-2010 09:48 AM
    down, goes
    • Replies: 1
    • Views: 1,621
    02-03-2010, 01:43 AM Go to last post
  10. Need help on my first built UHU servo

    Started by thaisolar‎, 03-22-2009 12:32 PM
    3 Pages
    1 2 3
    • Replies: 54
    • Views: 11,221
    01-03-2010, 05:58 AM Go to last post
  11. new build

    Started by gvb‎, 12-27-2009 06:52 AM
    • Replies: 4
    • Views: 2,253
    12-28-2009, 03:32 PM Go to last post
  12. E-STOP Circuit for the UHU

    Started by LZ1TWB‎, 11-05-2009 06:37 PM
    • Replies: 10
    • Views: 3,727
    12-01-2009, 03:41 PM Go to last post
  13. Power Schematic for Old UHU Please Advise

    Started by bill south‎, 11-06-2009 03:28 PM
    • Replies: 9
    • Views: 2,873
    11-08-2009, 10:26 AM Go to last post
  14. Kit purchase info

    Started by paul3112‎, 11-02-2009 08:16 PM
    • Replies: 1
    • Views: 1,779
    11-05-2009, 05:57 AM Go to last post
  15. Heatsinking the HP-UHU

    Started by H.O‎, 07-10-2008 03:23 PM
    • Replies: 16
    • Views: 5,416
    11-02-2009, 05:45 PM Go to last post
  16. Unhappy Need advice in my project

    Started by elchip‎, 10-27-2009 08:53 PM
    als, look, next, not
    • Replies: 1
    • Views: 1,657
    10-31-2009, 07:15 PM Go to last post
  17. Question UHU Low Power - They Work but how do I

    Started by bill south‎, 10-14-2009 11:23 AM
    • Replies: 7
    • Views: 2,348
    10-16-2009, 10:34 AM Go to last post
  18. i'm so lost!!!

    Started by Liron Alm‎, 08-10-2009 03:05 PM
    far, not, then
    • Replies: 2
    • Views: 2,164
    10-10-2009, 04:23 PM Go to last post
  19. Power supplies for UHU

    Started by contactirfu‎, 06-30-2008 05:35 AM
    9 Pages
    1 2 3 4 5 ... 9
    • Replies: 164
    • Views: 30,853
    09-18-2009, 03:05 AM Go to last post
  20. a good question about the UHU.HP

    Started by tenmetalman‎, 08-21-2009 09:31 PM
    current draw, far
    • Replies: 3
    • Views: 1,839
    08-22-2009, 11:27 AM Go to last post

Page 3 of 5 FirstFirst 12345 LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands