Current Schematcs & support information

Results 1 to 6 of 6

Thread: Current Schematcs & support information

  1. #1
    Registered
    Join Date
    Jan 2006
    Location
    USA
    Posts
    297
    Downloads
    0
    Uploads
    0

    Default Current Schematcs & support information

    Here's a the most current information on schematics,parts lists, parts revision,etc. Current Schematic I don't believe there's a current schematic with out some errors/changes. Here the best I can do. in the original UHU drive forum, complete schematic to rev.0B, post#1652. Power stage schematic to rev.0C, post#1690, Parts modification for Under 11amps continuous & 0ver 11 amps continuous, post#1887. and finely most current parts list, in the thread "Revised Bills of Material for HP UHU Drives" is the "UHU HP Revised Parts List 9-22-09.xls‎" is the latest & most accurate parts list showing all parts revisions as of today.
    Hope this helps
    Paul

    Similar Threads:


  2. #2
    Registered
    Join Date
    Jan 2006
    Location
    USA
    Posts
    297
    Downloads
    0
    Uploads
    0

    Default Schematic, Current rev. B + rev c for power stage

    Post #1 still is the correct information for the latest schematic support



  3. #3
    Registered
    Join Date
    Jan 2006
    Location
    USA
    Posts
    297
    Downloads
    0
    Uploads
    0

    Default Current Schematics

    Let's try this again. Hopefully here's the schematics for the UHU.HIGHPOWER
    PCB

    Attached Thumbnails Attached Thumbnails Current Schematcs & support information-img042-jpg   Current Schematcs & support information-img043-jpg   Current Schematcs & support information-img044-jpg   Current Schematcs & support information-img045-jpg  

    Current Schematcs & support information-img046-jpg   Current Schematcs & support information-img041-jpg  


  4. #4
    Registered
    Join Date
    Jan 2006
    Location
    USA
    Posts
    297
    Downloads
    0
    Uploads
    0

    Default wrong wiring on img.041.JPG, J8-J9 previous post

    I just noticed that the above drawing is labeled WRONG. see the enclosure with this post for the correct hook up. the drive shown is an old one when I was mounting the 470uF 200v capacitor on the P2 terminals due to a height clearance problems

    Attached Thumbnails Attached Thumbnails Current Schematcs & support information-img047-jpg  


  5. #5
    Registered
    Join Date
    Jan 2006
    Location
    USA
    Posts
    297
    Downloads
    0
    Uploads
    0

    Default this is the closest to a accurate schematic 7/24/2012I

    I think the above schematic the closest to a current schematic to what we're building



  6. #6
    Member
    Join Date
    Aug 2006
    Location
    USA
    Posts
    2758
    Downloads
    0
    Uploads
    0

    Default Re: Current Schematcs & support information

    New Modified HP_UHU current limit circuit schematics.

    High Power UHU Thread (HP.UHU) (post # 40)

    On the old schematics (Rev 1.0), attached to this thread, replace C28 (4.7uF) by a 2.2uF/25 v film capacitor, replace C29 by 470 pf ceramic capacitor and don't forget to connect the R16 lead to +15Vdc instead of +5Vdc.

    regards,

    kreutz



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Current Schematcs & support information

Current Schematcs & support information