UCCNC CALIBRATIONS FOR STEPPER MOTORS

Results 1 to 8 of 8

Thread: UCCNC CALIBRATIONS FOR STEPPER MOTORS

  1. #1

    Default UCCNC CALIBRATIONS FOR STEPPER MOTORS

    Hello Gents

    I have done the calibrations of the stepper motors, using a dial indicator, to measure the distance each stepper motor traveled. Used a steel ruler, to check the longer distances, which each axis traveled. All is 100% correct there.

    Now I machined a circular pocket of 20 mm dia. It measured 19 mm.

    Machine is in Constant Velocity Mode.

    The stepper motor drivers have been set for micro stepping.

    I do my designing in Fusion 360 and then send the file in a .nc format, to the UCCNC software.

    Any suggestions, to where or why this is happening?

    Regards

    Craig

    Similar Threads:


  2. #2

    Default Re: UCCNC CALIBRATIONS FOR STEPPER MOTORS

    Hi Gents

    I must mention that I was using a feed rate of 50 mm/min, which is very slow and used a 1/8" ball nose end mill @ 6000 Rpm. Machined a pocket into a piece of aluminium. Looks very nice, but 1 mm smaller in diameter, than the drawing. Very little chance of tool deflection in this scenario.

    The holes in the 16 mm MDF of the spoil board, was also smaller than what the drawing stated. Hense, the calibrations are 100%.

    All the axis`s are ball screws and rails.

    So the machine`s construction is rigid.

    Regards

    Craig



  3. #3
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35137
    Downloads
    1
    Uploads
    0

    Default Re: UCCNC CALIBRATIONS FOR STEPPER MOTORS

    Cut the same thing in the opposite direction, and see if it's the same size?

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  4. #4

    Default Re: UCCNC CALIBRATIONS FOR STEPPER MOTORS

    Hello Gerry

    Thank you. I will give that a try. One thing, which I did see, was that the spindle was turning clockwise, as it should do, but the end mill`s tool path was machining anti-clockwise.

    When I view the tool path in Fusion 360, I see two red arrows, pointing in an anti-clockwise direction. Must these arrows point in a clockwise direction?

    Regards

    Craig



  5. #5
    Member
    Join Date
    Jun 2015
    Location
    Sweden
    Posts
    938
    Downloads
    0
    Uploads
    0

    Default Re: UCCNC CALIBRATIONS FOR STEPPER MOTORS

    Check your Constant velocity parameters.



  6. #6

    Default Re: UCCNC CALIBRATIONS FOR STEPPER MOTORS

    Quote Originally Posted by ger21 View Post
    Cut the same thing in the opposite direction, and see if it's the same size?
    Hello Gerry

    I just ran the program again and this time, I made it cut in a clockwise direction. No difference in the measurements. Kept the feed rates exactly as they were.

    Regards

    Craig



  7. #7

    Default Re: UCCNC CALIBRATIONS FOR STEPPER MOTORS

    Hello OlfCNC

    I checked the constant velocity parameters and they are all still default settings. I have been using the constant velocity mode and not the exact stop mode. Maybe I should try that with the same tool path and see if the measurements changed?

    Regards

    Craig



  8. #8
    Member
    Join Date
    Jun 2015
    Location
    Sweden
    Posts
    938
    Downloads
    0
    Uploads
    0

    Default Re: UCCNC CALIBRATIONS FOR STEPPER MOTORS

    Quote Originally Posted by craig00747 View Post
    Hello OlfCNC

    I checked the constant velocity parameters and they are all still default settings. I have been using the constant velocity mode and not the exact stop mode. Maybe I should try that with the same tool path and see if the measurements changed?

    Regards

    Craig
    If you working in Inches then lower the Linear addition length and Linear unity length to 0.001
    If you working in millimeters then the default should be fine.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

UCCNC  CALIBRATIONS FOR STEPPER MOTORS

UCCNC  CALIBRATIONS FOR STEPPER MOTORS

UCCNC  CALIBRATIONS FOR STEPPER MOTORS