Kira VTC 30 - Page 11


Page 11 of 11 FirstFirst ... 891011
Results 121 to 124 of 124

Thread: Kira VTC 30

  1. #121
    Registered
    Join Date
    Mar 2011
    Location
    Hungary
    Posts
    6
    Downloads
    0
    Uploads
    0

    Default Re: Kira VTC 30

    Yes, I know that.
    I can not solve the tuning of the servo myself.
    1 set 12 mm spindle and nut = 700 Euro
    1 set 10 mm spindle and nut = 120 Euro



  2. #122
    Registered
    Join Date
    Oct 2015
    Posts
    212
    Downloads
    0
    Uploads
    0

    Cool Re: Kira VTC 30

    Time for a short update again with some pictures.

    I've used the machine a bit lately making usefull stuff at home. I have some customer projects incomming but doing series production is a PITA without a bandsaw so I'm holing back until that arrives First up is a passive cooling block for my 18650 spot welder. Next is a blind holder. The machine is performing great now

    Kira VTC 30-img_2534-jpgKira VTC 30-img_2549-jpg


    I installed a Renishaw TS20 probe on the machine and it's been so great. I tested to probe the same tool 5 times and it repeats down to within +/- 0.00015mm. It's designed for a lathe so I don't have the proper stylus for measuring tools yet. Have to figure out how to install the same gear as a TS27R probe has or just get a TS27R. If I where to install this permanently I need to have a conduit kit (steel braided tubing over the cable) but I can't figure out what kind of kit I need..

    Kira VTC 30-img_2606-jpgKira VTC 30-img_2674-jpg


    Some filter maintenance. I installed this because I saw NYC CNC recommended it in a video. It sure looks like it's working avoiding regrinding of chips that comes with coolant.
    Kira VTC 30-img_2642-jpg

    Filters on cooling fans for VFD and braking resistor was worse than I thought. I didn't have the proper filter material so I just soaked them in soap and let them dry overnight. It can't get any worse than it was ^^
    Kira VTC 30-img_2671-jpg

    Yesterday I got a little helper in the cnc room She was helping out on some probing macros on the whiteboard
    Kira VTC 30-img_2644-jpg

    Updated picture of my desk at the machine. Still lacking a lot but it's getting there At least I can spot the desk after I cleaned up some the other day Back to machining now
    Kira VTC 30-img_2672-jpg

    Attached Thumbnails Attached Thumbnails Kira VTC 30-img_2534-jpg   Kira VTC 30-img_2549-jpg   Kira VTC 30-img_2606-jpg   Kira VTC 30-img_2642-jpg  

    Kira VTC 30-img_2644-jpg   Kira VTC 30-img_2671-jpg   Kira VTC 30-img_2674-jpg   Kira VTC 30-img_2672-jpg  



  3. #123
    Registered
    Join Date
    Oct 2015
    Posts
    212
    Downloads
    0
    Uploads
    0

    Default Re: Kira VTC 30

    I've not been very good at updates here lately but I figured that I could add some pictures from todays project. I got a similar vice to the one I have so I can install two vices and run more parts in one operation. This required new clamps for the vice and since I could not use alu clamps I found some steel and went ahead to test that. I've never milled steel on this machine before so this was a new experience. I'm using a Gühring RF100 diver and a sandvik facemill for the job. It didn't have perfect finish but it's good enough for clamps. Need to study some on why there is some kind of "ringing" in the surface on both the sandvik and the RF100.

    Short video of the job here:




    Kira VTC 30-1-jpegKira VTC 30-2-jpegKira VTC 30-3-jpegKira VTC 30-5-jpegKira VTC 30-6-jpgKira VTC 30-7-jpegKira VTC 30-10-jpgKira VTC 30-11-jpeg

    Attached Thumbnails Attached Thumbnails Kira VTC 30-1-jpeg   Kira VTC 30-2-jpeg   Kira VTC 30-3-jpeg   Kira VTC 30-5-jpeg  

    Kira VTC 30-6-jpg   Kira VTC 30-7-jpeg   Kira VTC 30-10-jpg   Kira VTC 30-11-jpeg  



  4. #124
    Registered
    Join Date
    Oct 2015
    Posts
    5
    Downloads
    0
    Uploads
    0

    Default Re: Kira VTC 30

    Hi . read all of this respect!



Page 11 of 11 FirstFirst ... 891011

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Kira VTC 30

Kira VTC 30