Toyoda representative here if you have any questions - Page 3


Page 3 of 3 FirstFirst 123
Results 25 to 30 of 30

Thread: Toyoda representative here if you have any questions

  1. #25
    Registered
    Join Date
    Apr 2011
    Location
    USA
    Posts
    439
    Downloads
    0
    Uploads
    0

    Default Re: Toyoda representative here if you have any questions

    There is a switch inside the main panel that when flipped it step by step when you command multiple M06 in MDI mode. Each M06 will do a step in the tool change process. So put many M06 in MDI program page each followed by EOB. Put machine in single block mode and flip switch. Each time you press cycle start it will change the tool block by block.



  2. #26
    Registered
    Join Date
    Mar 2016
    Location
    United States
    Posts
    6
    Downloads
    0
    Uploads
    0

    Default Re: Toyoda representative here if you have any questions

    Hello Anthony, are you still checking the forum? I have a thread going about losing my zero positions on a FA-400 as well getting a AL94 alarm. I'm getting a little desperate as I'm not getting much support from Toyoda, and if I don't get this machine going soon, I will lose the job I bought it for. Any help much appreciated.

    Thanks, John



  3. #27
    Registered
    Join Date
    Sep 2017
    Location
    India
    Posts
    21
    Downloads
    0
    Uploads
    0

    Default Re: Toyoda representative here if you have any questions

    Dear All
    I need urgent help!!

    We recently bought a used Toyoda FA 550 with fanuc 15m with alpha drives from UK.

    When we power on this machine the system is not getting ready it shows this message:

    F15M14 A0C20
    ?

    I P L
    1. DUMP MEMORY
    2. SET FILE
    3. CLEAR FILE
    4. FILE
    5. SETTING
    6. END IPL
    ?

    Can anyone help how to resolve this problem.

    need an urgent help and response.

    Thnx

    vishal jain



  4. #28
    Registered jwskinner's Avatar
    Join Date
    Jan 2009
    Location
    U.S.
    Posts
    6
    Downloads
    0
    Uploads
    0

    Default

    We have a Toyoda 450s running a fanuc 30i controller. we opted for the 120 tool package. My question is , Are my tool positions fixed or can i float them into whatever open pod is available and the controller will track tool locations?



  5. #29
    Mjohnson1959's Avatar
    Join Date
    Sep 2018
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by Toyoda_Anthony View Post
    My name is Anthony and I am an employee from Toyoda Machinery USA. CNCzone recently created a sub-forum on the site for Toyoda and because of that; I’ll be the representative to address any questions or issues you might have.

    The information we gather from trade forums is very valuable to us, especially when designing machines. Having a forum such as this provides the feedback our engineers need to continue developing machines that meet the needs of consumers.

    If anyone ever has any questions about any Toyoda products, parts, or service, feel free to post on here, or message me directly and I will do my best to assist you. I’m going to make the effort to check the forum multiple times a week, so hopefully we can respond to your questions promptly.
    hello Anthony,i ave a gl5p-32 grinder.after having machine down for a while while replacing amp,came up with f002,g492 and a673.the batteries are up to proper voltage 3.6 v.wont let machine power up all the way.thanks



  6. #30
    Registered
    Join Date
    Apr 2012
    Location
    united states
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default

    Hello. I have a GC32 that has a A899 fault. At some point someone had reseated the pcu card. What is needed to clear this fault? PCU card is lit with the sgail, halt and locto.



  7. #31
    arpit123's Avatar
    Join Date
    Feb 2019
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default

    Is the machine working now



  8. #32
    arpit123's Avatar
    Join Date
    Feb 2019
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default

    is the machine working now?



Page 3 of 3 FirstFirst 123

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Toyoda representative here if you have any questions

Toyoda representative here if you have any questions