2" face mill does this spped and feed seem right? on pcnc 1100


Results 1 to 5 of 5

Thread: 2" face mill does this spped and feed seem right? on pcnc 1100

  1. #1
    Member
    Join Date
    Aug 2012
    Location
    USA
    Posts
    17
    Downloads
    0
    Uploads
    0

    Default 2" face mill does this spped and feed seem right? on pcnc 1100

    I have a Pcnc1100 S3, I bought a 3 flute 2" face mill to use on some 6061, It looks like I could run about 475rpms at 2ipm feed rate? does that seem about right? I don't know at what depth of cut.

    Similar Threads:


  2. #2
    Member soofle616's Avatar
    Join Date
    Mar 2020
    Posts
    92
    Downloads
    0
    Uploads
    0

    Default Re: 2" face mill does this spped and feed seem right? on pcnc 1100

    HSS or carbide?

    Fwiw I run my superfly (single carbide insert, roughly 2.6" diameter as currently configured) at 2500rpm. I get decent results from 12ipm at .075 DOC but if I want a really nice finish I come down to 10ipm and do a finish pass at .01-.005" DOC.



  3. #3
    Member
    Join Date
    Nov 2012
    Location
    United States
    Posts
    517
    Downloads
    0
    Uploads
    0

    Default Re: 2" face mill does this spped and feed seem right? on pcnc 1100

    For 475 rpm 3 flutes that sounds like a reasonable feed rate.
    For carbide inserts I think you should be able to spin faster, and increase feed rate to match, although it does matter whether you're skimming or hogging.
    Horsepower will limit how deep you can cut, and you get less of that the slower you spin. Then again, as speed and depth go up, torque goes down, so on small spindles, it generally needs some tuning to the specific setup, no matter what.

    475 rpm at 2" diameter is only 250 sfm, which is fine for tool steel in 6061 but you can push much faster with carbide. Try 2000 rpm and feed at 8 ipm, if you're surfacing/skimming, and using carbide inserts.



  4. #4

    Default Re: 2" face mill does this spped and feed seem right? on pcnc 1100

    What geometry/type is the face mill?



  5. #5
    Member AUSTINMACHINING's Avatar
    Join Date
    Mar 2011
    Location
    usa
    Posts
    473
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by LSX View Post
    I have a Pcnc1100 S3, I bought a 3 flute 2" face mill to use on some 6061, It looks like I could run about 475rpms at 2ipm feed rate? does that seem about right? I don't know at what depth of cut.
    Aluminum I ran max spindle speed with a 2" ripper mill. A good starting point would be max speed at .05 deep 1.8" step over at 30ipm. Flood cool if you can.I was using a solid r8 holder, not TTS



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

2" face mill does this spped and feed seem right? on pcnc 1100

2" face mill does this spped and feed seem right? on pcnc 1100

2" face mill does this spped and feed seem right? on pcnc 1100