Torchmate


Page 1 of 22 123411 ... LastLast
Threads 1 to 20 of 440

Forum: Torchmate

Discuss Torchmate machines here!

  1. My Torchmate 1 build log

    Started by blackhollowmfg‎, 02-08-2007 10:18 AM
    5 Pages
    1 2 3 4 5
    • Replies: 84
    • Views: 51,492
    05-29-2010, 11:25 AM Go to last post
  2. Question clip art for plasma cutting metal art work

    Started by balto‎, 06-21-2007 11:47 PM
    • Replies: 14
    • Views: 48,074
    08-19-2009, 09:28 AM Go to last post
  3. how good are the torchmate machines?

    Started by Apples‎, 11-03-2004 02:36 AM
    3 Pages
    1 2 3
    business, easy, peter, reliable, torchmate
    • Replies: 41
    • Views: 22,253
    08-08-2008, 01:14 AM Go to last post
  4. Is it really needed? Arc Voltage Torch Height Control

    Started by schoobie‎, 10-27-2007 05:22 PM
    non
    • Replies: 19
    • Views: 16,325
    10-04-2008, 11:11 PM Go to last post
    • Replies: 22
    • Views: 15,668
    04-18-2022, 06:54 PM Go to last post
  5. Newbie- Torchmate 2x2 w/Lincoln Tomahawk offer

    Started by Alleykat‎, 11-28-2011 03:31 AM
    • Replies: 9
    • Views: 15,266
    07-21-2015, 04:09 PM Go to last post
  6. DIY AVHC for Torchmate 2X2?

    Started by jurban‎, 12-21-2011 04:52 PM
    2 Pages
    1 2
    • Replies: 33
    • Views: 14,507
    09-21-2012, 05:24 AM Go to last post
  7. Question Circle With Bolt hole Pattern

    Started by JJsFab‎, 01-28-2008 02:18 PM
    • Replies: 6
    • Views: 14,428
    09-01-2013, 01:07 PM Go to last post
  8. Mike From Torchmate

    Started by Mike@Torchmate‎, 01-26-2007 03:49 PM
    3 Pages
    1 2 3
    department, everyone, machine, ques, quotes, sales, torchmate
    • Replies: 40
    • Views: 14,391
    02-24-2011, 12:41 PM Go to last post
  9. Problem- 501a signal generator question/problem

    Started by Jeonlyep‎, 01-06-2015 08:28 PM
    • Replies: 8
    • Views: 11,755
    02-18-2024, 07:29 PM Go to last post
  10. Exclamation Market for slightly used Torchmate 2 system?

    Started by Mr. G‎, 11-14-2007 08:51 PM
    available
    • Replies: 13
    • Views: 11,627
    03-27-2010, 10:21 PM Go to last post
  11. Am i expecting to much from my Torchmate??

    Started by DarkHorse‎, 01-28-2010 01:37 AM
    • Replies: 13
    • Views: 11,497
    02-15-2010, 11:01 AM Go to last post
  12. Problem- taper on plasma cuts using torchmate machine.

    Started by nauticwaterjet‎, 02-14-2013 02:49 PM
    • Replies: 14
    • Views: 11,431
    05-06-2014, 08:12 AM Go to last post
  13. New torchmate 1 build questions

    Started by weldthis‎, 11-22-2009 08:17 PM
    • Replies: 16
    • Views: 11,002
    05-27-2010, 01:55 PM Go to last post
  14. Torchmate not living up to expectations

    Started by PHSS‎, 02-08-2009 12:57 AM
    another, far, hired, its, mos, next, not, saying, since, then
    • Replies: 11
    • Views: 10,990
    09-19-2012, 04:29 PM Go to last post
  15. New Machine Build- ISO 401a or 501a Signal Generator

    Started by quickjam‎, 07-25-2020 10:08 PM
    401a, 501a, flashcut, life, torchmate
    • Replies: 4
    • Views: 10,864
    01-01-2021, 12:57 AM Go to last post
  16. Exclamation Plasma just shuts off during cutting cycle

    Started by crazydave‎, 10-22-2008 02:18 PM
    its, not
    • Replies: 6
    • Views: 9,692
    11-14-2008, 09:21 AM Go to last post
  17. Question Problem- Bad TM1 stepper motor?

    Started by MoparJon‎, 09-06-2008 10:33 PM
    available, down, indicate, its, maybe, plus, saw, since, then, took
    • Replies: 12
    • Views: 8,860
    04-30-2013, 01:47 PM Go to last post
  18. torchmate verses plasma cam

    Started by balto‎, 06-19-2007 07:57 AM
    • Replies: 19
    • Views: 8,634
    05-20-2008, 03:34 PM Go to last post
  19. New Machine Build- Well, I've finally started my TM 1 Build.

    Started by Shapenfab‎, 01-28-2008 03:23 PM
    • Replies: 16
    • Views: 8,622
    12-05-2009, 08:50 PM Go to last post

Page 1 of 22 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 3 users browsing this forum. (0 members & 3 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands