Techno CNC


Page 1 of 12 123411 ... LastLast
Threads 1 to 20 of 228

Forum: Techno CNC

Discuss Techno CNC machines here!

    • Replies: 0
    • Views: 84
    11-06-2018, 12:51 PM Go to last post
  1. Techno Davinci

    Started by smits25u‎, 10-29-2018 11:52 AM
    • Replies: 3
    • Views: 129
    11-05-2018, 03:00 PM Go to last post
  2. ISEL Gantry XYZ setup - need help identifying wheather servo or stepper

    Started by cncneon‎, 08-20-2018 06:13 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 485
    10-30-2018, 10:40 AM Go to last post
  3. Cleaning, Lubing, Spring question on ISEL

    Started by cncneon‎, 10-25-2018 10:35 AM
    ball, clean, notice, rails, spring
    • Replies: 0
    • Views: 83
    10-25-2018, 10:35 AM Go to last post
  4. ISEL CPM 4030 what soft to use ??

    Started by philippe_007‎, 06-07-2017 01:53 PM
    • Replies: 7
    • Views: 1,120
    10-07-2018, 02:23 PM Go to last post
  5. Help with 8 wire NEMA 23

    Started by cncneon‎, 10-04-2018 04:21 PM
    black, guess, red, stripe, white
    • Replies: 1
    • Views: 103
    10-04-2018, 05:32 PM Go to last post
  6. ISEL stepper question

    Started by cncneon‎, 08-30-2018 09:39 AM
    connector, mtr, phase, pins, stepper
    • Replies: 1
    • Views: 140
    08-30-2018, 12:00 PM Go to last post
  7. Dis-assembly of Gantry III table & frame?

    Started by dixdance‎, 07-26-2018 06:03 PM
    • Replies: 5
    • Views: 245
    07-27-2018, 07:51 PM Go to last post
    • Replies: 0
    • Views: 109
    06-17-2018, 03:23 PM Go to last post
    • Replies: 0
    • Views: 138
    05-30-2018, 06:28 PM Go to last post
  8. Need Help!- Reactivating old Isel router

    Started by Kaes‎, 04-04-2018 07:46 PM
    files, i‘ve, port, router, run
    • Replies: 1
    • Views: 340
    04-23-2018, 04:47 PM Go to last post
  9. Newbie- Techno-Isel DaVinci Update/Retrofit

    Started by PiZLe_‎, 02-18-2016 12:03 AM
    • Replies: 2
    • Views: 1,213
    04-22-2018, 09:51 AM Go to last post
  10. johnohara's Techno-Isel DaVinci

    Started by johnohara‎, 02-09-2014 03:58 PM
    2 Pages
    1 2
    • Replies: 20
    • Views: 9,555
    03-20-2018, 11:16 AM Go to last post
  11. Jerky motion with Davinci

    Started by dixdance‎, 01-21-2017 04:42 PM
    cnc, jerky, machine, motion, software
    • Replies: 8
    • Views: 665
    03-12-2018, 12:50 PM Go to last post
  12. Any advantage to replacing DaVinci stepper motors?

    Started by dixdance‎, 02-05-2018 06:01 PM
    advantage, motors, replacing, stepper, steppers
    • Replies: 1
    • Views: 257
    03-08-2018, 12:58 PM Go to last post
  13. Just In H20T43-SRV400 controller card differences

    Started by AMG Guitars‎, 03-04-2018 06:59 PM
    • Replies: 3
    • Views: 231
    03-06-2018, 03:56 PM Go to last post
  14. While I am waiting... here's my 4th axis

    Started by Dave's_Not_Here‎, 05-27-2010 08:26 PM
    • Replies: 9
    • Views: 3,503
    03-04-2018, 10:03 PM Go to last post
  15. SRV400 Libs C++

    Started by mikkojay‎, 12-10-2013 02:15 PM
    • Replies: 3
    • Views: 735
    03-04-2018, 05:53 PM Go to last post
  16. Post CNC HITACHI SEIKI 5NE turning center model 1100

    Started by yumuri‎, 09-30-2009 07:51 PM
    2 Pages
    1 2
    not, profesional, then
    • Replies: 12
    • Views: 5,231
    02-02-2018, 07:27 PM Go to last post
  17. Smile Problem- TECHNO.PST not proper.

    Started by AMG Guitars‎, 08-05-2017 10:04 AM
    • Replies: 9
    • Views: 687
    01-19-2018, 11:31 PM Go to last post

Page 1 of 12 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 2 users browsing this forum. (0 members & 2 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands