Need Help! Techno Series 400 ATC swap.


Results 1 to 5 of 5

Thread: Techno Series 400 ATC swap.

  1. #1
    Registered GuitarOtto's Avatar
    Join Date
    Jan 2019
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Techno Series 400 ATC swap.

    Hi Guys,
    I purchased a Turnkey Techno LC 3024 a few months back.
    Love the desktop machine, but would like to replace the HSD non tool changing spindle with an ATC.
    I'm assuming that you will be able to re-pin the spindle connection and find the connection
    for the ATC air solenoid on the control board and you are good to go? Any one know if there is thread on this?
    I looked at what ever is available on the Techno web with little luck. Thank you in advance, Otto

    Similar Threads:


  2. #2
    Member ericscottf's Avatar
    Join Date
    Sep 2012
    Location
    USA
    Posts
    214
    Downloads
    0
    Uploads
    0

    Default Re: Techno Series 400 ATC swap.

    Otto,

    We can help with this. We specialize in the original USA made Techno equipment.

    There is a dedicated extra control board for the toolchangers on Techno machines (we have stock), and can provide the rest of the info you'll need to get it going. Contact us from the form on our website at Armor CNC or call the number listed there.

    Regards
    Eric

    Eric Feldman - Design Engineer, Programmer
    Armor CNC - http://www.armorcnc.com Support hours: 7am thru 10pm EST, 7 days a week


  3. #3
    Registered GuitarOtto's Avatar
    Join Date
    Jan 2019
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Techno Series 400 ATC swap.

    Thanks Eric,
    I just left a message for you. Here is a couple pictures.
    One is the Machine and new ATC spindle. The other is the I/O Riser card.
    There are two connection points One is marked Spindle, one Coolant.
    Coolant relay is simple enough.
    Could this "Spindle" be the low voltage for the solonoid?

    Attached Thumbnails Attached Thumbnails Techno Series 400 ATC swap.-techno1-jpg   Techno Series 400 ATC swap.-techno-jpg  


  4. #4
    Member ericscottf's Avatar
    Join Date
    Sep 2012
    Location
    USA
    Posts
    214
    Downloads
    0
    Uploads
    0

    Default Re: Techno Series 400 ATC swap.

    Hello,

    I didn't see a message. How did you send it?

    Spindle is not for the solenoid. That's for spindle speed control. You don't have the board for toolchanger sensors/solenoid control. You can get it from us if you like.

    Eric Feldman - Design Engineer, Programmer
    Armor CNC - http://www.armorcnc.com Support hours: 7am thru 10pm EST, 7 days a week


  5. #5
    Registered GuitarOtto's Avatar
    Join Date
    Jan 2019
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Techno Series 400 ATC swap.

    Eric,
    left you a voice mail.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Techno Series 400 ATC swap.

Techno Series 400 ATC swap.