My Taig Setup And Ready To Go!


Page 1 of 2 12 LastLast
Results 1 to 12 of 23

Thread: My Taig Setup And Ready To Go!

  1. #1
    Registered WOODKNACK's Avatar
    Join Date
    Mar 2003
    Location
    Maine
    Posts
    271
    Downloads
    0
    Uploads
    0

    Default My Taig Setup And Ready To Go!

    Well I have finished all the wires and everything is lubed and greesed. The machine is ready to go! I have engraved a few names with it so far. I am very impressed with it. nice little rig!

    Similar Threads:
    Attached Thumbnails Attached Thumbnails My Taig Setup And Ready To Go!-taig-mill-done-001-jpg  
    My little piece of the web!
    http://users.adelphia.net/~wjdupont



  2. #2
    Registered ToyMaker's Avatar
    Join Date
    May 2003
    Location
    United States
    Posts
    325
    Downloads
    0
    Uploads
    0

    Default

    Yo! way to go WoodKnack, you old motor-spinner, you.

    robotic regards,

    Tom



  3. #3
    Registered cncadmin's Avatar
    Join Date
    Mar 2003
    Location
    United States
    Posts
    6855
    Downloads
    3
    Uploads
    4

    Default

    Nice set-up!

    Thank You,
    Paul G

    Check out-
    [URL="http://www.signs101.com"]www.signs101.com[/URL]


  4. #4
    Registered
    Join Date
    May 2003
    Posts
    15
    Downloads
    0
    Uploads
    0

    Default

    To sweet! I'm jealous!!



  5. #5
    Registered Klox's Avatar
    Join Date
    Mar 2003
    Location
    NZ
    Posts
    507
    Downloads
    0
    Uploads
    0

    Default

    Looks very, very good!!!

    Klox

    *** KloX ***
    I'm lazy, I'm only "sparking" when the EDM is running....


  6. #6
    Registered cncadmin's Avatar
    Join Date
    Mar 2003
    Location
    United States
    Posts
    6855
    Downloads
    3
    Uploads
    4

    Default

    What are the boxes under the stepper motors?

    Thank You,
    Paul G

    Check out-
    [URL="http://www.signs101.com"]www.signs101.com[/URL]


  7. #7
    Registered balsaman's Avatar
    Join Date
    Mar 2003
    Location
    Canada
    Posts
    2139
    Downloads
    0
    Uploads
    0

    Default

    Looks great. Are you sure that's yours? Looks like a pic from a web page or something. Too clean to be a real shop...



    Eric

    I wish it wouldn't crash.


  8. #8
    Registered WOODKNACK's Avatar
    Join Date
    Mar 2003
    Location
    Maine
    Posts
    271
    Downloads
    0
    Uploads
    0

    Default YUP ITS MINE! LOL

    Those boxes I got at Radio Shack. They are just small project boxes. I drilled a hole on the bottom of the box and put the stepper motor wires thru the hole. then doubleside tape to the stepper I then have another hole on the other end for the wire that comes from my controller. I wire capped on all the wires and screwed the cover to the box on. Takes the strain off the wires and looks very neat I think!
    Nothing looks worse then seeing wire just hanging! I like to do a neat job. While I was waiting for my mill to arrrive I repainted my bench. Thats why it looks so clean.

    My little piece of the web!
    http://users.adelphia.net/~wjdupont



  9. #9
    Registered Rekd's Avatar
    Join Date
    Apr 2003
    Location
    teh Debug Window
    Posts
    1876
    Downloads
    0
    Uploads
    0

    Default

    Wow. Very nice job.



    'Rekd

    Matt
    San Diego, Ca

    ___ o o o_
    [l_,[_____],
    l---L - □lllllll□-
    ( )_) ( )_)--)_)

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  10. #10
    Registered WOODKNACK's Avatar
    Join Date
    Mar 2003
    Location
    Maine
    Posts
    271
    Downloads
    0
    Uploads
    0

    Default FIRST GEAR!!!

    Here is a timing wheel gear for a clock I cut out on my Taig mill.
    MY GOOD FRIEND STEVE sent me the gcodes for it. Thanks Steve. So far I am very impressed with the whole mill!! Picture is kind of blurry. Sorry..

    Attached Thumbnails Attached Thumbnails My Taig Setup And Ready To Go!-timingwheel2-jpg  
    My little piece of the web!
    http://users.adelphia.net/~wjdupont



  11. #11
    Registered Klox's Avatar
    Join Date
    Mar 2003
    Location
    NZ
    Posts
    507
    Downloads
    0
    Uploads
    0

    Default Gear

    Woodknack,
    I had to change my display card, your image looks better now! (just kidding!)

    Looks like your machine cuts very well, the shape of the gear teeth is out of the ordinary. Well done!
    It's the first time I see teeth like this.
    I think i must send all my gearcutting jobs to you.....LOL

    Klox

    *** KloX ***
    I'm lazy, I'm only "sparking" when the EDM is running....


  12. #12
    Registered balsaman's Avatar
    Join Date
    Mar 2003
    Location
    Canada
    Posts
    2139
    Downloads
    0
    Uploads
    0

    Default

    What material is that cut from?

    Eric

    I wish it wouldn't crash.


Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

My Taig Setup And Ready To Go!

My Taig Setup And Ready To Go!