Stepper Motors / Drives - Page 11


Page 11 of 236 FirstFirst ... 8910111213142161111 ... LastLast
Threads 201 to 220 of 4714

Forum: Stepper Motors / Drives

Discuss stepper motors, drivers and related topics here.

  1. Sticky Threads
  2. Sticky Thread Sticky: What stepper motor should I use thread

    Started by cncadmin‎, 01-27-2005 04:51 PM
    4 Pages
    1 2 3 4
    • Replies: 62
    • Views: 92,727
    09-18-2019, 01:52 PM Go to last post
  3. Sticky Thread Sticky: What effect does microstepping have on torque?

    Started by Stuff-Builder‎, 10-04-2005 10:54 AM
    5 Pages
    1 2 3 4 5
    • Replies: 87
    • Views: 136,920
    10-24-2015, 07:11 PM Go to last post
  4. Forum Threads
  1. Replacing steppers for more torque options / Advice wanted

    Started by DAAD‎, 12-30-2020 03:16 PM
    3 Pages
    1 2 3
    • Replies: 53
    • Views: 4,220
    01-24-2021, 06:19 PM Go to last post
  2. Need Help!- More trouble shooting needed.

    Started by boydage‎, 01-13-2021 03:36 PM
    running, motor, steps, resolution, loop
    • Replies: 1
    • Views: 310
    01-14-2021, 07:21 PM Go to last post
  3. Which drivers are best for nema 23 motors?

    Started by jaru-eri‎, 01-10-2021 03:14 AM
    alternatives, give, loosing, motors, speed
    • Replies: 5
    • Views: 893
    01-12-2021, 06:53 AM Go to last post
  4. 8 wire stepper and drive overheating

    Started by Tristar500‎, 01-11-2021 01:22 PM
    ago, cnc, stepper, wire, years
    • Replies: 3
    • Views: 469
    01-11-2021, 08:16 PM Go to last post
  5. Thoughts on Nema 24 resolution please?

    Started by boydage‎, 01-08-2021 01:44 AM
    nema, resolution, screws, setting, spr
    • Replies: 2
    • Views: 904
    01-09-2021, 03:15 AM Go to last post
  6. 10 best drivers on the market??

    Started by jaru-eri‎, 01-09-2021 12:38 AM
    drivers, market, regarded
    • Replies: 0
    • Views: 676
    01-09-2021, 12:38 AM Go to last post
  7. sizing and choosing closed loop motors.

    Started by AchillesGr‎, 01-03-2021 10:39 AM
    3nm, cnc, diference, nema, series
    • Replies: 5
    • Views: 1,036
    01-04-2021, 12:01 PM Go to last post
  8. Need Help!- What do you expect from Chinese components?

    Started by sparrowlegs‎, 01-01-2021 04:39 AM
    • Replies: 5
    • Views: 1,230
    01-02-2021, 03:23 PM Go to last post
  9. Looking for 10A stepper driver leadshine?

    Started by DAAD‎, 12-30-2020 04:45 AM
    amp, driver, drivers, good, stepper
    • Replies: 4
    • Views: 936
    12-30-2020, 03:17 PM Go to last post
  10. Trinamics tmc5160

    Started by Mike_jay‎, 12-28-2020 05:51 AM
    cnc, gcode, motion control, tmc5160, trinamics
    • Replies: 0
    • Views: 377
    12-28-2020, 05:51 AM Go to last post
  11. Closed loop stepper positioning

    Started by bochketuning‎, 12-16-2020 06:37 PM
    • Replies: 5
    • Views: 671
    12-18-2020, 02:25 PM Go to last post
    • Replies: 1
    • Views: 2,470
    12-18-2020, 07:19 AM Go to last post
  12. Need Help!- Broken shaft on NEMA 23!

    Started by rockaukum‎, 11-16-2020 08:18 PM
    box, motor, motors, nema, shaft
    • Replies: 6
    • Views: 1,595
    12-17-2020, 06:23 PM Go to last post
  13. Stepper grinding randomly

    Started by Jfactor‎, 11-19-2020 02:49 PM
    grinding, parallel, port, running, stepper
    • Replies: 1
    • Views: 731
    12-17-2020, 02:57 AM Go to last post
  14. Lightbulb Need Help!- How to set alarm wires HBS860H ?

    Started by burgija1213‎, 12-16-2020 11:38 AM
    • Replies: 0
    • Views: 982
    12-16-2020, 11:38 AM Go to last post
  15. Need Help!- Sutai m542 driver

    Started by emba-media‎, 12-01-2020 07:18 PM
    controller, dir-, driver, m542, sutai
    • Replies: 0
    • Views: 918
    12-01-2020, 07:18 PM Go to last post
  16. Only movement in one direction on all 3 axes

    Started by MicroJAB‎, 11-21-2020 06:36 PM
    • Replies: 0
    • Views: 825
    11-21-2020, 06:36 PM Go to last post
    • Replies: 3
    • Views: 560
    11-18-2020, 04:44 PM Go to last post

Page 11 of 236 FirstFirst ... 8910111213142161111 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 59 users browsing this forum. (0 members & 59 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands