Stepper Motors / Drives


Page 1 of 226 12341151101 ... LastLast
Threads 1 to 20 of 4513

Forum: Stepper Motors / Drives

Discuss stepper motors, drivers and related topics here.

  1. Sticky Threads
  2. Sticky Thread Sticky: What stepper motor should I use thread

    Started by cncadmin‎, 01-27-2005 04:51 PM
    4 Pages
    1 2 3 4
    • Replies: 62
    • Views: 66,155
    09-18-2019, 01:52 PM Go to last post
  3. Sticky Thread Sticky: What effect does microstepping have on torque?

    Started by Stuff-Builder‎, 10-04-2005 10:54 AM
    5 Pages
    1 2 3 4 5
    • Replies: 87
    • Views: 89,250
    10-24-2015, 07:11 PM Go to last post
  4. Forum Threads
  1. Need Help!- CL86T Driver Issues - Closed Loop Stepper Driver

    Started by Dreco‎, Yesterday 01:40 AM
    cnc, driver, error, issue, running
    • Replies: 0
    • Views: 114
    Yesterday, 01:40 AM Go to last post
  2. Need Help!- Serial communication with HBS860H closoed loop driver

    Started by mkaluza2‎, 08-07-2020 12:47 PM
    alternate, default, driver, model, software
    • Replies: 1
    • Views: 212
    10-24-2020, 05:45 PM Go to last post
  3. Closed loop steppers for CNC routers question.

    Started by umnik‎, 10-23-2020 02:43 PM
    advantages, cnc, fine, motor, routers
    • Replies: 2
    • Views: 131
    10-24-2020, 08:14 AM Go to last post
  4. Need Help!- MB3 + ESS wiring

    Started by FSS‎, 12-23-2019 06:41 PM
    • Replies: 7
    • Views: 552
    10-18-2020, 11:45 AM Go to last post
  5. connector wires on NEMA 23

    Started by DerFarm‎, 09-23-2020 01:06 PM
    • Replies: 3
    • Views: 230
    10-15-2020, 03:51 AM Go to last post
  6. Post Need Help!- Stepper motor only rotating one direction (RAMPS 1.4 Board)

    Started by L4_Topher‎, 01-08-2016 05:04 PM
    • Replies: 8
    • Views: 10,563
    10-12-2020, 11:10 AM Go to last post
  7. Need Help!- Nema 34

    Started by Saarneu93‎, 10-09-2020 12:23 PM
    • Replies: 12
    • Views: 275
    10-10-2020, 04:02 PM Go to last post
  8. Need Help!- Stepper kit power supply question

    Started by tatinc2000‎, 10-04-2020 09:15 PM
    diy, power, power supply, router, stepper
    • Replies: 1
    • Views: 168
    10-04-2020, 10:17 PM Go to last post
  9. Need Help!- up grade

    Started by wetwillie‎, 10-03-2020 06:34 AM
    controller, date, drivers, motors, steeper
    • Replies: 0
    • Views: 115
    10-03-2020, 06:34 AM Go to last post
  10. Closed loop Stepper holding torque enquiry

    Started by marbles‎, 10-01-2020 02:22 PM
    closed, hold, loop, software, stepper
    • Replies: 5
    • Views: 298
    10-03-2020, 04:14 AM Go to last post
  11. New Machine Build- AXBB-E to Leadshine MX3660 problem

    Started by BWW808‎, 10-02-2020 01:52 AM
    #axbbe #leadshinemx3660, cnc, mx3660, pins, problem
    • Replies: 0
    • Views: 124
    10-02-2020, 01:52 AM Go to last post
  12. Cool Help with tuning Stepper motor& Drive on UCCNC AXIS X,Y,Z

    Started by akihiko‎, 08-17-2020 01:30 AM
    2 Pages
    1 2
    • Replies: 25
    • Views: 775
    09-22-2020, 12:14 AM Go to last post
  13. NEED HELP Mach3 and 2HSS86H problem on AXBB-E

    Started by Alexi‎, 09-21-2020 05:42 AM
    5v0, config, mach3, motor, problem
    • Replies: 0
    • Views: 112
    09-21-2020, 05:42 AM Go to last post
  14. Need Help!- Stepper motor sizing based on load travel time and distance

    Started by dpressm‎, 09-16-2020 04:31 PM
    • Replies: 2
    • Views: 144
    09-18-2020, 06:43 AM Go to last post
  15. More Stepper Motor Woes

    Started by derekj308‎, 03-27-2006 07:37 AM
    2-8, 3.75, cause, mos, motors, set, step, turn, within
    • Replies: 7
    • Views: 3,914
    09-14-2020, 07:35 PM Go to last post
  16. anaheim nema 23 with driver 23md 106s to bob board

    Started by gv71‎, 09-05-2020 08:16 PM
    • Replies: 1
    • Views: 166
    09-14-2020, 07:30 PM Go to last post
    • Replies: 6
    • Views: 229
    09-13-2020, 08:55 PM Go to last post

Page 1 of 226 12341151101 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 30 users browsing this forum. (1 members & 29 guests)

  1. apt403

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands