Stepper Motors / Drives


Page 1 of 219 12341151101 ... LastLast
Threads 1 to 20 of 4380

Forum: Stepper Motors / Drives

Discuss stepper motors, drivers and related topics here.

  1. Sticky Threads
  2. Sticky Thread Sticky: What stepper motor should I use thread

    Started by cncadmin‎, 01-27-2005 04:51 PM
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 61
    • Views: 60,803
    12-02-2018, 05:10 PM Go to last post
  3. Sticky Thread Sticky: What effect does microstepping have on torque?

    Started by Stuff-Builder‎, 10-04-2005 10:54 AM
    8 Pages
    1 2 3 4 5 ... 8
    • Replies: 87
    • Views: 79,083
    10-24-2015, 07:11 PM Go to last post
  4. Forum Threads
    • Replies: 0
    • Views: 57
    Yesterday, 02:51 PM Go to last post
  1. How do I ID the leads on a 8-wire stepper?

    Started by rexstep‎, 08-13-2019 11:01 PM
    config, leads, pairs, resistance, wiring
    • Replies: 5
    • Views: 158
    08-16-2019, 09:04 PM Go to last post
  2. Apparent cross-motor stepper feedback in CNC axes.

    Started by salukikev‎, 08-13-2019 02:11 AM
    • Replies: 4
    • Views: 216
    08-15-2019, 04:23 PM Go to last post
    • Replies: 5
    • Views: 246
    08-13-2019, 04:22 PM Go to last post
  3. Question Newbie- Power Supply Size?

    Started by pbrgle1‎, 08-07-2019 12:50 PM
    explanation, motors, power, stepper, supply
    • Replies: 6
    • Views: 256
    08-11-2019, 11:13 AM Go to last post
  4. Need Help!- No stepper movement.

    Started by KidKhaos‎, 07-28-2019 11:11 PM
    • Replies: 10
    • Views: 401
    08-11-2019, 08:10 AM Go to last post
    • Replies: 5
    • Views: 175
    08-10-2019, 05:00 AM Go to last post
  5. Need help with Eastern Air Devices Stepper motors

    Started by drf24‎, 08-09-2019 06:01 AM
    air, eastern, motors, ohms, wires
    • Replies: 0
    • Views: 60
    08-09-2019, 06:01 AM Go to last post
  6. Need Help!- New Machine Build No movement. Please Help.

    Started by dbtoutfit‎, 08-06-2019 10:13 PM
    cnc, dm542t driver, not moving, pin, stepper drivers
    • Replies: 0
    • Views: 100
    08-06-2019, 10:13 PM Go to last post
    • Replies: 4
    • Views: 896
    08-01-2019, 03:25 PM Go to last post
  7. Need Help!- stepper motor is running noisy !

    Started by Telsiz‎, 07-24-2019 08:22 AM
    • Replies: 4
    • Views: 226
    07-29-2019, 08:39 AM Go to last post
    • Replies: 2
    • Views: 185
    07-27-2019, 09:59 PM Go to last post
  8. Need Help!- Are there steppers any good

    Started by Kristjan1505‎, 07-22-2019 05:38 AM
    fast, good, manufacturer, noob, osmtec
    • Replies: 5
    • Views: 244
    07-25-2019, 05:03 PM Go to last post
  9. Need Help!- TX14207 SCHEMATIC

    Started by NormanA‎, 06-14-2017 11:49 PM
    • Replies: 9
    • Views: 3,746
    07-24-2019, 12:21 PM Go to last post
  10. Alternative sources for Stepper Driver signals.

    Started by Pader‎, 07-22-2019 01:51 AM
    arduino, controller, stepper control, stepper controller, switching
    • Replies: 1
    • Views: 153
    07-22-2019, 07:09 PM Go to last post
  11. Problem with cranking up the current for steppers

    Started by tangi‎, 05-08-2019 09:55 AM
    2 Pages
    1 2
    • Replies: 16
    • Views: 580
    07-19-2019, 09:41 AM Go to last post
  12. Question Need Help!- Search stepper motor 23HD450Y-31A1

    Started by jakubsara‎, 07-15-2019 09:24 AM
    • Replies: 2
    • Views: 140
    07-15-2019, 10:10 AM Go to last post
  13. Question CNC kit purchased - I have electrical questions.

    Started by t3kboi‎, 07-09-2019 05:44 PM
    cnc, higher, run, steppers, voltage
    • Replies: 5
    • Views: 246
    07-10-2019, 08:36 AM Go to last post
  14. Question Newbie- DM542T Differential Input

    Started by Project_Hopeless‎, 07-09-2019 10:02 PM
    differential, dir, dm542t, drive, input
    • Replies: 0
    • Views: 121
    07-09-2019, 10:02 PM Go to last post
  15. Question Newbie- Need help with stepper drive setup

    Started by iMatt‎, 07-03-2019 09:23 AM
    cnc, control, motors, nema, stepper
    • Replies: 4
    • Views: 230
    07-05-2019, 10:32 AM Go to last post

Page 1 of 219 12341151101 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 47 users browsing this forum. (0 members & 47 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands