Stepper Motors / Drives


Page 1 of 222 12341151101 ... LastLast
Threads 1 to 20 of 4423

Forum: Stepper Motors / Drives

Discuss stepper motors, drivers and related topics here.

  1. Sticky Threads
  2. Sticky Thread Sticky: What stepper motor should I use thread

    Started by cncadmin‎, 01-27-2005 05:51 PM
    4 Pages
    1 2 3 4
    • Replies: 62
    • Views: 62,874
    09-18-2019, 02:52 PM Go to last post
  3. Sticky Thread Sticky: What effect does microstepping have on torque?

    Started by Stuff-Builder‎, 10-04-2005 11:54 AM
    5 Pages
    1 2 3 4 5
    • Replies: 87
    • Views: 82,302
    10-24-2015, 08:11 PM Go to last post
  4. Forum Threads
    • Replies: 9
    • Views: 208
    Yesterday, 05:47 AM Go to last post
    • Replies: 2
    • Views: 174
    02-11-2020, 07:37 PM Go to last post
  1. Is this too much noise? (video)

    Started by 5Carbides‎, 02-07-2020 05:47 AM
    idle, noise, powered, sitting, video
    • Replies: 3
    • Views: 441
    02-08-2020, 04:40 PM Go to last post
    • Replies: 0
    • Views: 139
    01-31-2020, 12:31 AM Go to last post
  2. Newbie- Stepper / Driver configuration for a HY-6040 rebuild

    Started by Shawn_M‎, 10-16-2018 04:43 PM
    2 Pages
    1 2
    • Replies: 27
    • Views: 1,969
    01-28-2020, 05:30 AM Go to last post
  3. Need Help!- Choosing new steppers for DIY machine

    Started by Wildmine‎, 01-04-2020 06:09 PM
    kit, motors, nema34, speed, steppers
    • Replies: 4
    • Views: 276
    01-27-2020, 03:01 AM Go to last post
  4. X axis making noise and not moving

    Started by RhFab‎, 01-05-2020 05:00 PM
    cnc, move, moving, start, stepper
    • Replies: 1
    • Views: 261
    01-19-2020, 03:38 PM Go to last post
  5. Need help with stepper sizing

    Started by adnanolol‎, 01-16-2020 06:30 AM
    • Replies: 3
    • Views: 182
    01-17-2020, 03:44 AM Go to last post
  6. Need Help!- Need spec sheet for stepper motors

    Started by Escritar‎, 04-26-2018 06:38 PM
    • Replies: 8
    • Views: 1,236
    01-13-2020, 10:20 PM Go to last post
  7. Wantai SS880 closed loop stepper drive tuning

    Started by danilom‎, 05-27-2019 04:13 PM
    connect, software, ss880, tuning, wantai
    • Replies: 2
    • Views: 350
    01-06-2020, 03:59 PM Go to last post
  8. Need Help!- MB3 + ESS wiring

    Started by FSS‎, 12-23-2019 07:41 PM
    • Replies: 4
    • Views: 215
    01-05-2020, 10:13 AM Go to last post
  9. Need Help!- Stepper stalls high speed

    Started by Petro1head‎, 01-01-2020 11:40 AM
    2 Pages
    1 2
    • Replies: 26
    • Views: 627
    01-04-2020, 10:49 AM Go to last post
  10. Lack of Torque, Missing Steps

    Started by beeker‎, 01-03-2020 09:27 PM
    bad motors, driver, power supply, stepper, torque
    • Replies: 1
    • Views: 132
    01-04-2020, 05:51 AM Go to last post
  11. THB6064AH JP-6445A driver

    Started by Wesk18‎, 12-30-2014 01:47 PM
    • Replies: 5
    • Views: 2,531
    12-22-2019, 08:09 AM Go to last post
  12. Need help as usual with motors

    Started by sbloom67‎, 12-20-2019 12:27 AM
    motor, motors, power, set, start
    • Replies: 1
    • Views: 279
    12-20-2019, 02:12 AM Go to last post
  13. Wiring dilema

    Started by Lord9o‎, 11-20-2015 09:17 AM
    • Replies: 5
    • Views: 617
    12-16-2019, 04:28 AM Go to last post
  14. Need Help!- Are resisters needed?

    Started by vpl‎, 12-09-2019 09:57 PM
    • Replies: 8
    • Views: 388
    12-10-2019, 05:09 PM Go to last post
  15. Recommend Motors and Drivers for CNC Router

    Started by JDFarmBoy‎, 02-06-2019 03:30 PM
    cnc, drivers, motors, plan, router
    • Replies: 6
    • Views: 633
    12-10-2019, 04:27 PM Go to last post
    • Replies: 4
    • Views: 382
    12-09-2019, 03:12 PM Go to last post
  16. Newbie- Nema 34 closed loop driver alarm problem(HBS86H)

    Started by Lnt‎, 03-09-2019 01:51 PM
    • Replies: 6
    • Views: 1,134
    12-09-2019, 09:21 AM Go to last post

Page 1 of 222 12341151101 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 64 users browsing this forum. (1 members & 63 guests)

  1. desertmoose

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands