Which drivers are best for nema 23 motors?


Results 1 to 6 of 6

Thread: Which drivers are best for nema 23 motors?

  1. #1
    Member
    Join Date
    May 2006
    Location
    NORWAY
    Posts
    285
    Downloads
    0
    Uploads
    0

    Default Which drivers are best for nema 23 motors?

    Up to now I´ve been using Gecko G540 but I need to know if there are any better alternatives which will give a faster speed to my motors without loosing steps.

    Similar Threads:


  2. #2
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35447
    Downloads
    1
    Uploads
    0

    Default Re: Which drivers are best for nema 23 motors?

    If you are trying to get the most speed, you need to increase voltage to the motors. Different drives won't make that much difference.
    Different motors can make much more difference than different drives.

    What are the specs of the motors you have, and what voltage power supply are you using?

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  3. #3
    Member
    Join Date
    May 2006
    Location
    NORWAY
    Posts
    285
    Downloads
    0
    Uploads
    0

    Default Re: Which drivers are best for nema 23 motors?

    The steppers are KL23H276-30-8B and the power supply is marked S350-48 7.3A I measured the output voltage to 44V.



  4. #4
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35447
    Downloads
    1
    Uploads
    0

    Default Re: Which drivers are best for nema 23 motors?

    Do you have them wired bipolar parallel?
    You probably wouldn't see much difference going to a drive that can supply the rated 4.2a, unless you also increase the voltage to around 70V. And at that point, I'd find a motor with more torque as well.

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  5. #5
    Member
    Join Date
    May 2006
    Location
    NORWAY
    Posts
    285
    Downloads
    0
    Uploads
    0

    Default Re: Which drivers are best for nema 23 motors?

    OK.
    Do you think that mine stepper mototrs are to small for a Taig mill? Which motors would you recommend?



  6. #6
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    35447
    Downloads
    1
    Uploads
    0

    Default Re: Which drivers are best for nema 23 motors?

    No, they should be fine for a Taig.

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Which drivers are best for nema 23 motors?

Which drivers are best for nema 23 motors?

Which drivers are best for nema 23 motors?