Spindles / VFD


Page 1 of 49 123411 ... LastLast
Threads 1 to 20 of 972

Forum: Spindles / VFD

Discuss Router, Spindle and VFD Controllers here!

  1. Why does my VFD overheat when running at low RPM?

    Started by TTalma‎, Yesterday 10:09 AM
    2 Pages
    1 2
    hot, machine, overheating, spindle, vfd
    • Replies: 15
    • Views: 187
    Today, 09:48 AM Go to last post
  2. Cheating with inverter

    Started by mick41zxr‎, Today 07:13 AM
    50hz, constant, inverter, motor, torque
    • Replies: 2
    • Views: 52
    Today, 08:33 AM Go to last post
  3. New spindle motor - Servo or Induction?

    Started by spumco‎, 08-06-2018 06:00 PM
    4 Pages
    1 2 3 4
    • Replies: 39
    • Views: 639
    Today, 07:39 AM Go to last post
  4. 3kw motor and vfd

    Started by Atomas0907‎, 07-23-2018 09:38 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 611
    08-12-2018, 04:40 PM Go to last post
  5. Power 500W Spindle from 1/5kW VFD

    Started by ajayre‎, 08-12-2018 04:24 AM
    power, spindle, vfd, voltage, working
    • Replies: 2
    • Views: 90
    08-12-2018, 07:24 AM Go to last post
  6. WS55-220 BLDC Driver Mains Connection

    Started by ajayre‎, 08-11-2018 11:43 AM
    bldc, driver, live, neutral, wire
    • Replies: 0
    • Views: 72
    08-11-2018, 11:43 AM Go to last post
  7. Hitachi SJ200

    Started by mick41zxr‎, 08-08-2018 04:23 AM
    400v, hitachi, motor, phase, run
    • Replies: 0
    • Views: 82
    08-08-2018, 04:23 AM Go to last post
  8. Can't get Mach3 to Control VFD

    Started by nikos8‎, 02-25-2017 02:04 PM
    • Replies: 7
    • Views: 649
    08-07-2018, 01:14 PM Go to last post
  9. AT1-2200X VFD on/off and speed wiring enquiry

    Started by marbles‎, 07-31-2018 08:30 AM
    • Replies: 2
    • Views: 121
    08-07-2018, 06:16 AM Go to last post
  10. Thanks mactec54

    Started by shipshed‎, 07-30-2018 12:31 PM
    mactec54, pin, spindle, stop, working
    • Replies: 6
    • Views: 202
    07-31-2018, 04:38 PM Go to last post
    • Replies: 8
    • Views: 782
    07-31-2018, 06:40 AM Go to last post
  11. Help with Chinese Spindle and C6 Board

    Started by Biggermens‎, 07-29-2018 06:27 PM
    • Replies: 0
    • Views: 119
    07-29-2018, 06:27 PM Go to last post
  12. Direct Drive Spindle

    Started by nzhuhu‎, 07-29-2018 09:19 AM
    direct, drive, mistake, post, spindle
    • Replies: 0
    • Views: 128
    07-29-2018, 09:19 AM Go to last post
  13. New ATC spindle (Yay!)

    Started by bhurts‎, 07-26-2018 10:29 PM
    • Replies: 1
    • Views: 142
    07-27-2018, 05:26 PM Go to last post
  14. Cheap and Simple ATC for Chinese Spindle

    Started by bogan‎, 10-06-2012 12:40 AM
    4 Pages
    1 2 3 4
    • Replies: 39
    • Views: 33,467
    07-27-2018, 12:42 AM Go to last post
  15. VFD single phase input three phase output

    Started by ZeroBacklash‎, 07-14-2018 10:38 AM
    4 Pages
    1 2 3 4
    input, phase, single, vfd, vfds
    • Replies: 42
    • Views: 745
    07-26-2018, 12:22 PM Go to last post
  16. GRBL controller 0-10v spindle

    Started by bdbell‎, 07-19-2018 10:17 PM
    • Replies: 1
    • Views: 179
    07-20-2018, 04:20 AM Go to last post
  17. Need Help!- Connecting Mesa 7i83 for analog control of a servo.

    Started by rcheli‎, 07-15-2018 08:37 PM
    7i83, aout, dyn4, thought
    • Replies: 2
    • Views: 123
    07-15-2018, 10:23 PM Go to last post
    • Replies: 7
    • Views: 211
    07-15-2018, 01:37 PM Go to last post
  18. Question Correct VFD for 5HP Motor with Single Phase Input

    Started by JJ0704‎, 05-09-2018 11:13 PM
    3 Pages
    1 2 3
    • Replies: 29
    • Views: 865
    07-14-2018, 11:44 PM Go to last post

Page 1 of 49 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 27 users browsing this forum. (6 members & 21 guests)

  1. kementze,
  2. nkrogers,
  3. iwaskevin,
  4. Bubba,
  5. TTalma,
  6. mick41zxr

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands