Spindles / VFD


Page 1 of 63 12341151 ... LastLast
Threads 1 to 20 of 1246

Forum: Spindles / VFD

Discuss Router, Spindle and VFD Controllers here!

  1. Need Help!- What's the story on 1.5kW 110V VFDs?

    Started by batcrave‎, Today 12:53 AM
    chinese, huanyang, recommendations, shopping, vfd
    • Replies: 3
    • Views: 94
    Today, 11:35 AM Go to last post
  2. VFD interface to other equipment.

    Started by diyhands‎, 02-10-2018 02:28 PM
    5 Pages
    1 2 3 4 5
    • Replies: 89
    • Views: 5,757
    03-30-2020, 05:17 PM Go to last post
  3. Colombo RS 110.22 ISO 30

    Started by bobmagnuson‎, 11-07-2017 02:46 PM
    iso, layout, pin, sensor, spindle
    • Replies: 1
    • Views: 299
    03-30-2020, 01:25 AM Go to last post
  4. Need Help!- ELTE spindle / Invertek E3 VFD setup/parameters

    Started by Sam-HHI‎, 03-29-2020 05:34 AM
    • Replies: 0
    • Views: 51
    03-29-2020, 05:34 AM Go to last post
  5. Controlling spindle from Mach 3

    Started by areinike‎, 01-30-2014 04:27 PM
    • Replies: 17
    • Views: 10,413
    03-28-2020, 05:00 PM Go to last post
    • Replies: 0
    • Views: 48
    03-28-2020, 03:32 PM Go to last post
    • Replies: 7
    • Views: 276
    03-21-2020, 10:12 AM Go to last post
  6. WJ200 wiring to G540

    Started by jckstrthmghty‎, 03-17-2020 01:11 AM
    correct, ground, terminal, wiring, wj200
    • Replies: 2
    • Views: 142
    03-17-2020, 07:36 AM Go to last post
  7. Need Help!- 220v vfd wiring

    Started by Chmexdf5633‎, 03-15-2020 06:25 PM
    • Replies: 2
    • Views: 186
    03-16-2020, 04:44 PM Go to last post
  8. RnRMotion breakout board and STEPPERONLINE VFD

    Started by StefanoPrato‎, 03-14-2020 10:01 AM
    • Replies: 2
    • Views: 123
    03-14-2020, 06:52 PM Go to last post
  9. chinese 2kW spindle motor repair

    Started by reg.miller‎, 02-25-2020 06:59 AM
    air, bearing, chinese, motor, spindle
    • Replies: 17
    • Views: 530
    03-06-2020, 04:24 PM Go to last post
  10. New Machine Build- spindle motor wiring help please

    Started by r1jlewis‎, 03-06-2020 02:19 PM
    • Replies: 0
    • Views: 150
    03-06-2020, 02:19 PM Go to last post
  11. Chinese 2.2kw spindle burned out?

    Started by justCNCit‎, 09-08-2019 01:54 PM
    7 Pages
    1 2 3 4 5 ... 7
    • Replies: 126
    • Views: 4,729
    03-02-2020, 03:56 AM Go to last post
  12. Need Help!- Makita RT700

    Started by Tazdingo‎, 02-29-2020 02:40 PM
    • Replies: 1
    • Views: 224
    02-29-2020, 03:33 PM Go to last post
  13. Red face Need Help!- please help HQD GDL70-24Z/9.0 wiring diagram / instalation manual

    Started by viso‎, 02-25-2020 07:13 PM
    • Replies: 2
    • Views: 148
    02-26-2020, 02:20 PM Go to last post
  14. Post Need Help!- Huanyang VFD + Spindle 2.2kw + NVUM + Mach3 settings

    Started by markokaz‎, 02-05-2020 04:20 PM
    • Replies: 15
    • Views: 703
    02-26-2020, 09:40 AM Go to last post
  15. Show me your water cooling setup!

    Started by nemisladkiv‎, 01-18-2020 06:55 AM
    • Replies: 3
    • Views: 423
    02-25-2020, 07:49 PM Go to last post
    • Replies: 2
    • Views: 248
    02-25-2020, 01:03 AM Go to last post
    • Replies: 15
    • Views: 393
    02-24-2020, 03:23 PM Go to last post
  16. Need Help!- Sunfar E300

    Started by pwwww‎, 02-23-2020 11:42 AM
    e300, head, replace, sunfar, yellow
    • Replies: 0
    • Views: 99
    02-23-2020, 11:42 AM Go to last post

Page 1 of 63 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 44 users browsing this forum. (6 members & 38 guests)

  1. Jim Dawson,
  2. pugz,
  3. George484,
  4. ger21,
  5. brouser1

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands