Spindles / VFD


Page 1 of 63 12341151 ... LastLast
Threads 1 to 20 of 1254

Forum: Spindles / VFD

Discuss Router, Spindle and VFD Controllers here!

    • Replies: 5
    • Views: 64
    Today, 05:25 PM Go to last post
  1. Need Help!- HY 1.5kw 220V *NO DISPLAY* AT ALL

    Started by AlexanderJohn‎, Yesterday 04:19 PM
    • Replies: 6
    • Views: 123
    Today, 11:01 AM Go to last post
  2. Need Help!- Yaskawa 626VM3 Repair?

    Started by giz‎, 06-14-2016 11:25 AM
    2 Pages
    1 2
    • Replies: 38
    • Views: 3,011
    Today, 05:28 AM Go to last post
  3. VFD Wiring to generic BoB

    Started by Daniko88‎, 04-06-2020 01:12 PM
    • Replies: 9
    • Views: 129
    Yesterday, 12:56 PM Go to last post
  4. Hy 400hz vfd + 2.2kw spindle +300eth-ub1

    Started by HuguesP‎, Yesterday 07:07 AM
    10v, 22800rpm, issue, signal, vfd
    • Replies: 2
    • Views: 67
    Yesterday, 07:26 AM Go to last post
  5. Colombo ATC Spindle help....

    Started by ganzerd‎, 04-09-2015 04:42 PM
    • Replies: 2
    • Views: 785
    Yesterday, 02:33 AM Go to last post
  6. Help! AC bldc driver to 48v motor

    Started by crl1_1‎, 04-06-2020 10:31 PM
    • Replies: 3
    • Views: 110
    04-06-2020, 11:29 PM Go to last post
    • Replies: 12
    • Views: 227
    04-06-2020, 01:29 PM Go to last post
  7. Need Help!- What's the story on 1.5kW 110V VFDs?

    Started by batcrave‎, 04-01-2020 12:53 AM
    • Replies: 19
    • Views: 372
    04-06-2020, 11:04 AM Go to last post
    • Replies: 3
    • Views: 164
    04-06-2020, 06:39 AM Go to last post
  8. VFD interface to other equipment.

    Started by diyhands‎, 02-10-2018 02:28 PM
    5 Pages
    1 2 3 4 5
    • Replies: 98
    • Views: 6,042
    04-04-2020, 09:22 AM Go to last post
  9. VFD Parameters for Denford Orac lathe

    Started by GarageCNC‎, 04-02-2020 11:56 AM
    frequency, motor, param, speed, vfd
    • Replies: 2
    • Views: 106
    04-02-2020, 04:48 PM Go to last post
  10. @MACTEC54 your PM box is full

    Started by tkms002‎, 02-22-2019 04:01 PM
    @mactec54, box, full, mactec54
    • Replies: 5
    • Views: 246
    04-02-2020, 04:40 PM Go to last post
  11. water pump for HY02d223b VFD for 2,2 kw Spindle

    Started by ggeh‎, 04-02-2020 10:25 AM
    50hz, 60hz, pump, spindle, water
    • Replies: 0
    • Views: 82
    04-02-2020, 10:25 AM Go to last post
  12. Vfd YL620-a initial setup

    Started by Terryble24‎, 07-02-2019 08:58 AM
    • Replies: 8
    • Views: 1,819
    04-01-2020, 09:11 PM Go to last post
  13. Colombo RS 110.22 ISO 30

    Started by bobmagnuson‎, 11-07-2017 02:46 PM
    iso, layout, pin, sensor, spindle
    • Replies: 1
    • Views: 311
    03-30-2020, 01:25 AM Go to last post
  14. Need Help!- ELTE spindle / Invertek E3 VFD setup/parameters

    Started by Sam-HHI‎, 03-29-2020 05:34 AM
    • Replies: 0
    • Views: 70
    03-29-2020, 05:34 AM Go to last post
  15. Controlling spindle from Mach 3

    Started by areinike‎, 01-30-2014 04:27 PM
    • Replies: 17
    • Views: 10,441
    03-28-2020, 05:00 PM Go to last post
    • Replies: 7
    • Views: 285
    03-21-2020, 10:12 AM Go to last post
  16. WJ200 wiring to G540

    Started by jckstrthmghty‎, 03-17-2020 01:11 AM
    correct, ground, terminal, wiring, wj200
    • Replies: 2
    • Views: 147
    03-17-2020, 07:36 AM Go to last post

Page 1 of 63 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 32 users browsing this forum. (5 members & 27 guests)

  1. p_lipa,
  2. Jim Dawson,
  3. tpaszkiewicz,
  4. CitizenOfDreams,
  5. jbar

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands