Spindles / VFD


Page 1 of 74 12341151 ... LastLast
Threads 1 to 20 of 1477

Forum: Spindles / VFD

Discuss Router, Spindle and VFD Controllers here!

  1. EMI noise, grounding, connection problems with new VFD 2.2kw spindle

    Started by cholme‎, 05-24-2021 09:34 PM
    2 Pages
    1 2
    • Replies: 34
    • Views: 697
    Today, 08:46 AM Go to last post
  2. Post Need Help!- Perske Spindle repair

    Started by antonyvm‎, Yesterday 12:37 AM
    • Replies: 0
    • Views: 92
    Yesterday, 12:37 AM Go to last post
  3. XSY-AT1 programming tips

    Started by tarawa‎, 06-04-2019 11:13 AM
    • Replies: 6
    • Views: 4,300
    06-20-2021, 06:38 PM Go to last post
  4. Huanyang GT Series VFD keypad Pot does nothing

    Started by hawillk‎, 06-19-2021 05:44 PM
    • Replies: 13
    • Views: 189
    06-20-2021, 06:27 PM Go to last post
  5. DIY Automatic tool changing router spindle system

    Started by Chris D‎, 05-23-2021 02:42 PM
    changing, chinese, spindle, system, videos
    • Replies: 5
    • Views: 307
    06-20-2021, 07:25 AM Go to last post
  6. Huanyang Chinese VFD settings and manual here!

    Started by diyengineer‎, 12-14-2010 05:38 AM
    38 Pages
    1 2 3 4 5 ... 38
    • Replies: 748
    • Views: 254,161
    06-17-2021, 02:22 AM Go to last post
  7. Need Help!- Error E stop presset

    Started by ottohans‎, 06-15-2021 03:09 AM
    error, motors, router, runs, spindle
    • Replies: 2
    • Views: 117
    06-15-2021, 05:18 PM Go to last post
  8. Need Help!- VFD wiring with MB3 and ESS

    Started by darko9000‎, 06-07-2021 08:02 PM
    2 Pages
    1 2
    • Replies: 29
    • Views: 599
    06-14-2021, 07:29 PM Go to last post
  9. VFD 110V-110V parameters setting

    Started by Gautier‎, 10-03-2018 12:56 PM
    • Replies: 5
    • Views: 1,325
    06-14-2021, 07:23 PM Go to last post
  10. Newbie- Metal Working Spindle

    Started by KiwiEngineer‎, 06-01-2021 06:08 PM
    2 Pages
    1 2
    • Replies: 25
    • Views: 690
    06-09-2021, 11:53 PM Go to last post
  11. Need Help!- Mach3 resetting

    Started by kabbarnes‎, 06-05-2021 02:40 PM
    circuit, cnc, reset, spindle, vfd
    • Replies: 4
    • Views: 232
    06-05-2021, 11:42 PM Go to last post
  12. Need Help!- Need Spindle Recommendation for Cutting Stone

    Started by 0aw0‎, 05-26-2021 06:06 PM
    • Replies: 4
    • Views: 206
    05-27-2021, 03:46 PM Go to last post
  13. VFD to run a air compressor. Proper hookup

    Started by Barefootboy4‎, 05-25-2021 07:29 AM
    • Replies: 6
    • Views: 217
    05-26-2021, 09:58 AM Go to last post
  14. Spindle drive: potentiometer replacement

    Started by rschwarz‎, 05-23-2021 07:23 AM
    0-10v, analog, board, breakout, control, ground, input, potentiometer, spindle
    • Replies: 3
    • Views: 438
    05-23-2021, 07:01 PM Go to last post
    • Replies: 0
    • Views: 183
    05-18-2021, 10:34 AM Go to last post
  15. Spindle making squeeking noise when vfd is on

    Started by hautamak‎, 05-14-2021 02:37 PM
    control, direction, motor, spindle, stop
    • Replies: 13
    • Views: 400
    05-16-2021, 02:46 PM Go to last post
  16. VFD troubleshooting

    Started by cholme‎, 05-06-2021 05:52 PM
    • Replies: 8
    • Views: 361
    05-10-2021, 08:20 PM Go to last post
  17. Still a bit unclear on proper spindle grounding

    Started by QuinnSjoblom‎, 02-04-2018 10:09 PM
    2 Pages
    1 2
    • Replies: 24
    • Views: 4,340
    05-10-2021, 12:12 PM Go to last post
  18. Exclamation Need Help!- Single Phase Motor on AT2-1500X

    Started by oliverfink‎, 05-03-2021 01:56 AM
    at2-1500x, motor, phase, single, vfd
    • Replies: 0
    • Views: 213
    05-03-2021, 01:56 AM Go to last post

Page 1 of 74 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 12 users browsing this forum. (0 members & 12 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands