Spindles / VFD


Page 1 of 49 123411 ... LastLast
Threads 1 to 20 of 974

Forum: Spindles / VFD

Discuss Router, Spindle and VFD Controllers here!

  1. Wiring HuangYang VFD without grounding! How dangerous is this?

    Started by takeda‎, 05-29-2018 03:27 PM
    4 Pages
    1 2 3 4
    • Replies: 38
    • Views: 997
    Today, 11:04 AM Go to last post
    • Replies: 3
    • Views: 70
    Today, 09:00 AM Go to last post
  2. Why does my VFD overheat when running at low RPM?

    Started by TTalma‎, 08-14-2018 10:09 AM
    2 Pages
    1 2
    hot, machine, overheating, spindle, vfd
    • Replies: 22
    • Views: 354
    Yesterday, 07:45 PM Go to last post
  3. New spindle motor - Servo or Induction?

    Started by spumco‎, 08-06-2018 06:00 PM
    4 Pages
    1 2 3 4
    • Replies: 47
    • Views: 825
    08-17-2018, 03:19 PM Go to last post
  4. Need Help!- CNC Spindle Information Help Differences

    Started by Wisker‎, 08-15-2018 01:56 PM
    110v, 220v, cnc, hobby, setup
    • Replies: 1
    • Views: 88
    08-15-2018, 06:26 PM Go to last post
  5. Cheating with inverter

    Started by mick41zxr‎, 08-15-2018 07:13 AM
    50hz, constant, inverter, motor, torque
    • Replies: 2
    • Views: 94
    08-15-2018, 08:33 AM Go to last post
  6. 3kw motor and vfd

    Started by Atomas0907‎, 07-23-2018 09:38 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 626
    08-12-2018, 04:40 PM Go to last post
  7. Power 500W Spindle from 1/5kW VFD

    Started by ajayre‎, 08-12-2018 04:24 AM
    power, spindle, vfd, voltage, working
    • Replies: 2
    • Views: 101
    08-12-2018, 07:24 AM Go to last post
  8. WS55-220 BLDC Driver Mains Connection

    Started by ajayre‎, 08-11-2018 11:43 AM
    bldc, driver, live, neutral, wire
    • Replies: 0
    • Views: 74
    08-11-2018, 11:43 AM Go to last post
  9. Hitachi SJ200

    Started by mick41zxr‎, 08-08-2018 04:23 AM
    400v, hitachi, motor, phase, run
    • Replies: 0
    • Views: 86
    08-08-2018, 04:23 AM Go to last post
  10. Can't get Mach3 to Control VFD

    Started by nikos8‎, 02-25-2017 02:04 PM
    • Replies: 7
    • Views: 655
    08-07-2018, 01:14 PM Go to last post
  11. AT1-2200X VFD on/off and speed wiring enquiry

    Started by marbles‎, 07-31-2018 08:30 AM
    • Replies: 2
    • Views: 131
    08-07-2018, 06:16 AM Go to last post
  12. Thanks mactec54

    Started by shipshed‎, 07-30-2018 12:31 PM
    mactec54, pin, spindle, stop, working
    • Replies: 6
    • Views: 203
    07-31-2018, 04:38 PM Go to last post
    • Replies: 8
    • Views: 788
    07-31-2018, 06:40 AM Go to last post
  13. Help with Chinese Spindle and C6 Board

    Started by Biggermens‎, 07-29-2018 06:27 PM
    • Replies: 0
    • Views: 123
    07-29-2018, 06:27 PM Go to last post
  14. Direct Drive Spindle

    Started by nzhuhu‎, 07-29-2018 09:19 AM
    direct, drive, mistake, post, spindle
    • Replies: 0
    • Views: 133
    07-29-2018, 09:19 AM Go to last post
  15. New ATC spindle (Yay!)

    Started by bhurts‎, 07-26-2018 10:29 PM
    • Replies: 1
    • Views: 147
    07-27-2018, 05:26 PM Go to last post
  16. Cheap and Simple ATC for Chinese Spindle

    Started by bogan‎, 10-06-2012 12:40 AM
    4 Pages
    1 2 3 4
    • Replies: 39
    • Views: 33,499
    07-27-2018, 12:42 AM Go to last post
  17. VFD single phase input three phase output

    Started by ZeroBacklash‎, 07-14-2018 10:38 AM
    4 Pages
    1 2 3 4
    input, phase, single, vfd, vfds
    • Replies: 42
    • Views: 766
    07-26-2018, 12:22 PM Go to last post
  18. GRBL controller 0-10v spindle

    Started by bdbell‎, 07-19-2018 10:17 PM
    • Replies: 1
    • Views: 194
    07-20-2018, 04:20 AM Go to last post

Page 1 of 49 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 17 users browsing this forum. (1 members & 16 guests)

  1. mem4wwf

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands