Huanyang GT Pressure switch connection?


Results 1 to 6 of 6

Thread: Huanyang GT Pressure switch connection?

  1. #1
    Member
    Join Date
    Jun 2009
    Location
    USA
    Posts
    110
    Downloads
    0
    Uploads
    0

    Default Huanyang GT Pressure switch connection?

    Hello everyone,
    Need some guidance please. I'm setting up a new Quincy air compressor QT-7.5HP. Please review the attached pictures from manual. It's all wired up to a new Huanyang GT 7.5KW and runs fine from keyboard. I know other persons have wired control to the pressure switch but not quite sure which 2 terminals to connect. Can someone lend some advise here!

    Thanks in advance

    Steve in Maine and it's snowing!!

    Similar Threads:
    Attached Thumbnails Attached Thumbnails Huanyang GT Pressure switch connection?-control-jpg   Huanyang GT Pressure switch connection?-wiring-jpg  


  2. #2
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang GT Pressure switch connection?

    Quote Originally Posted by Barefootboy4 View Post
    Hello everyone,
    Need some guidance please. I'm setting up a new Quincy air compressor QT-7.5HP. Please review the attached pictures from manual. It's all wired up to a new Huanyang GT 7.5KW and runs fine from keyboard. I know other persons have wired control to the pressure switch but not quite sure which 2 terminals to connect. Can someone lend some advise here!

    Thanks in advance

    Steve in Maine and it's snowing!!
    It would be S1 and Com this can only be a switch with no voltage, so check the pressure switch that in the closed position there is no voltage across the 2 connections of the switch

    You will then have to change a Parameter for remote control

    P0.01=1 this may need to be 2

    P05.01=1

    Mactec54


  3. #3
    Member
    Join Date
    Jun 2009
    Location
    USA
    Posts
    110
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang GT Pressure switch connection?

    Quote Originally Posted by mactec54 View Post
    It would be S1 and Com this can only be a switch with no voltage, so check the pressure switch that in the closed position there is no voltage across the 2 connections of the switch

    You will then have to change a Parameter for remote control

    P0.01=1 this may need to be 2

    P05.01=1
    Thanks for the help.
    It worked!



  4. #4
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang GT Pressure switch connection?

    Quote Originally Posted by Barefootboy4 View Post
    Thanks for the help.
    It worked!
    Which Parameters did you use, just for my notes?

    Mactec54


  5. #5

    Default Re: Huanyang GT Pressure switch connection?

    Quote Originally Posted by Barefootboy4 View Post
    Thanks for the help.
    It worked!
    Any chance you can forward your parameters? I am doing the same Pressure Switch wiring and those 2 parameters aren't enough to get anything to happen. Thank you!



  6. #6
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang GT Pressure switch connection?

    Quote Originally Posted by contilon View Post
    Any chance you can forward your parameters? I am doing the same Pressure Switch wiring and those 2 parameters aren't enough to get anything to happen. Thank you!
    Are you using the same VFD Drive and what are your motor specs

    Mactec54


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Huanyang GT Pressure switch connection?

Huanyang GT Pressure switch connection?