Problem Error 11 - Motor protection parameter P9-01 or Small frequency converter selection


Results 1 to 4 of 4

Thread: Error 11 - Motor protection parameter P9-01 or Small frequency converter selection

  1. #1
    Member bescorza's Avatar
    Join Date
    Aug 2021
    Posts
    2
    Downloads
    0
    Uploads
    0

    Question Error 11 - Motor protection parameter P9-01 or Small frequency converter selection

    Hi there!
    I have a 3 axis CNC6090 with a 2.2 kw spindle.
    Recently, after a 5 hours strait operation, the spindle became to work as half energy and I immediately turn it off.
    After that, every attempt to run the spindle, the VFD pannel notified the "ERROR 13".
    With this situation, I looked after some youtube videos and try to find what was about. At the same time, I change some parameters in VFD and that was a big mistake.
    So, I decide to contact the factory (ChinaCNCzone or SCOTLE TECHNOLOGY). They gave me the path to reset all the parameters and recover the originals parameters. In addition, they explain to me that the "error 13" was a bad connection on the splindle cable or plugs.
    Well, checking the continuity, I found the problem. The cable no. 3 was interrupted.
    Problem solved
    But not! Now, my VFD is showing the "error 11". That means 2 options: Motor protection parameter P9-01 or Small frequency converter selection
    Is there someone that knows this parameters?

    HELP, PLEASE!

    Similar Threads:
    Attached Thumbnails Attached Thumbnails Error 11 - Motor protection parameter P9-01 or Small frequency converter selection-whatsapp-image-2021-07-30-11-43-a   Error 11 - Motor protection parameter P9-01 or Small frequency converter selection-whatsapp-image-2021-07-30-11-43-a  


  2. #2
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    12947
    Downloads
    0
    Uploads
    0

    Default Re: Error 11 - Motor protection parameter P9-01 or Small frequency converter selectio

    Quote Originally Posted by bescorza View Post
    Hi there!
    I have a 3 axis CNC6090 with a 2.2 kw spindle.
    Recently, after a 5 hours strait operation, the spindle became to work as half energy and I immediately turn it off.
    After that, every attempt to run the spindle, the VFD pannel notified the "ERROR 13".
    With this situation, I looked after some youtube videos and try to find what was about. At the same time, I change some parameters in VFD and that was a big mistake.
    So, I decide to contact the factory (ChinaCNCzone or SCOTLE TECHNOLOGY). They gave me the path to reset all the parameters and recover the originals parameters. In addition, they explain to me that the "error 13" was a bad connection on the splindle cable or plugs.
    Well, checking the continuity, I found the problem. The cable no. 3 was interrupted.
    Problem solved
    But not! Now, my VFD is showing the "error 11". That means 2 options: Motor protection parameter P9-01 or Small frequency converter selection
    Is there someone that knows this parameters?

    HELP, PLEASE!
    Do you have the VFD Manual PDF post it here
    It sounds like you may have some spindle motor damage do you have a Ground / Earth wire on the spindle this must use a 4 wire shielded cable

    What is the name of the VFD Drive they are using

    Mactec54


  3. #3
    Member bescorza's Avatar
    Join Date
    Aug 2021
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default Re: Error 11 - Motor protection parameter P9-01 or Small frequency converter selectio

    Thanks Mactec54 for your help!
    About de VFD Manual, I just found this topic: https://www.cnczone.com/forums/spind...gs-manual.html
    Unfortunately, this is not my VFD...

    About the wire, I'm using the 4 ways cable, stock, with that aviation plugs, also stock...

    Where can I find the drive? I'm asking this because my machine has a DSP controller.



  4. #4
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    12947
    Downloads
    0
    Uploads
    0

    Default Re: Error 11 - Motor protection parameter P9-01 or Small frequency converter selectio

    Quote Originally Posted by bescorza View Post
    Thanks Mactec54 for your help!
    About de VFD Manual, I just found this topic: https://www.cnczone.com/forums/spind...gs-manual.html
    Unfortunately, this is not my VFD...

    About the wire, I'm using the 4 ways cable, stock, with that aviation plugs, also stock...

    Where can I find the drive? I'm asking this because my machine has a DSP controller.
    The DSP controller is not what runs your spindle there will be a VFD Drive inside the box

    There are many VFD Drives you can not just pick one you have to know what you have , yes it is not a Huanyang as the Parameters are not correct for that VFD Drive

    Mactec54


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Error 11 - Motor protection parameter P9-01 or Small frequency converter selection

Error 11 - Motor protection parameter P9-01 or Small frequency converter selection

Error 11 - Motor protection parameter P9-01 or Small frequency converter selection