Chinese Huanyang 110v 1.5KW VFD Wiring with TB6600 (Red board)


Results 1 to 2 of 2

Thread: Chinese Huanyang 110v 1.5KW VFD Wiring with TB6600 (Red board)

  1. #1
    scotty3388's Avatar
    Join Date
    Apr 2021
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Chinese Huanyang 110v 1.5KW VFD Wiring with TB6600 (Red board)

    Hello folks,

    End up, I have a mix of Huanyang 110v 15KW spindle with motor and TB6560 stepper motor Controller board. Anyone know how should I connect the line in between 2 devices. I have a 10v, Gnd, AV1 on the TB6560 controller board, and many connections on VFD. Their manual is not helpful at all. do I need to change any setting on Mach 3 software?

    Your advise is greatly appreciated. Product photo is here https://photos.app.goo.gl/V3RcoySjgsvUNCEh8

    Current setup is

    Huanyang HY01D511B(110v, 1.5kw
    TB6560 Stepper Motor controller board
    Mach 3 software.

    Attached Thumbnails Attached Thumbnails Chinese  Huanyang 110v 1.5KW VFD Wiring with  TB6600 (Red board)-2021-04-27-16-13-42-jpg   Chinese  Huanyang 110v 1.5KW VFD Wiring with  TB6600 (Red board)-2021-04-27-16-13-31-jpg   Chinese  Huanyang 110v 1.5KW VFD Wiring with  TB6600 (Red board)-img_20200624_142834-jpg   Chinese  Huanyang 110v 1.5KW VFD Wiring with  TB6600 (Red board)-s-l1600-jpg  



  2. #2
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Chinese Huanyang 110v 1.5KW VFD Wiring with TB6600 (Red board)

    Quote Originally Posted by scotty3388 View Post
    Hello folks,

    End up, I have a mix of Huanyang 110v 15KW spindle with motor and TB6560 stepper motor Controller board. Anyone know how should I connect the line in between 2 devices. I have a 10v, Gnd, AV1 on the TB6560 controller board, and many connections on VFD. Their manual is not helpful at all. do I need to change any setting on Mach 3 software?

    Your advise is greatly appreciated. Product photo is here https://photos.app.goo.gl/V3RcoySjgsvUNCEh8

    Current setup is

    Huanyang HY01D511B(110v, 1.5kw
    TB6560 Stepper Motor controller board
    Mach 3 software.
    I don't think you have a PWM 0-10v Analog output on that board

    It looks like you have a Relay which could turn the VFD Drive on put no speed control

    So disconnect the wires you have installed or you might damage something

    Get the Relay turning On / Off, then connect it to FOR and DCM with Twisted Pair wires of the no more than 18 Gauge or 1mm stranded wire

    Mactec54


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Chinese  Huanyang 110v 1.5KW VFD Wiring with  TB6600 (Red board)

Chinese  Huanyang 110v 1.5KW VFD Wiring with  TB6600 (Red board)