Chinese 3 Phase 3KW VFD spindle Settings needed after reset

[casperround]

I own a 3KW 3 Phase chinese Spindle, a EYS8043-18/3.0 spindle
It has 2 Poles, 3 Phase, 300Hz, 8.6A, 3 Kw, 18000 R/min.

the VFD is a 220V 3KW Vfd supplied with the spindle. I accidently factory reset and cannot get the settings right anymore, the manual has nothing but the VFD factory settings not related at all to the spindle.


Similar Threads:

• Problem- Trouble with 2.2kw Chinese spindle, need help with VFD settings
• 3kw Chinese Spindle, Is it really 3kw
• 3kw spindle on a 4kw vfd
• Chinese 3KW spindle + Hitachi VFD question
• I have a 3kw spindle with a xin ye YPC3d72g VFD(need settings to get rpms to show)

[mactec54]

I own a 3KW 3 Phase chinese Spindle, a EYS8043-18/3.0 spindle
It has 2 Poles, 3 Phase, 300Hz, 8.6A, 3 Kw, 18000 R/min.

the VFD is a 220V 3KW Vfd supplied with the spindle. I accidently factory reset and cannot get the settings right anymore, the manual has nothing but the VFD factory settings not related at all to the spindle.

This is quit straight forward, don't keep trying it or you will smoke the spindle

I'm guessing this is an air cooled spindle, doing a factory reset did not change anything as all VFD Drives are at factory Default when you get them

So need to know the make / manufacture and model of the VFD Drive

What are the Parameters first 2 Letters

[casperround]

Written on the side of the VFD are these:

HY03D023B
2PH AC 220 + 20% 50Hz + 5Hz
3PH 0-220AC 3KW 13A 0.50 * 400.00Hz
400 - 606 - 8887

Yes it is a 3KW Air cooled spindle.

[mactec54]

Written on the side of the VFD are these:

HY03D023B
2PH AC 220 + 20% 50Hz + 5Hz
3PH 0-220AC 3KW 13A 0.50 * 400.00Hz
400 - 606 - 8887

Yes it is a 3KW Air cooled spindle.

What are the Parameters first 2 Letters Is it ( PD ) this will tell me if you have a genuine HY VFD Drive there are may HY copies and have different Parameter settings

[casperround]

Sorry, yes in the VFD settings it is PD

[mactec54]

Sorry, yes in the VFD settings it is PD

This should get you going this is a full set there may need to be some adjustments

Huanyang Mactec54
Input Power Connection Single Phase
Terminals R and T Plus Ground
3Kw Air Cooled 18,000 RPM

PD000=0 for Parameter unlock ( 1 ) for Parameter Lock

PD001=0 (1 For Remote Control)

PD002=0 ( 1 For 0-10v Terminal Control or Remote Trim Pot Control )
( J1 Also Needs to be set for Terminal Control )

PD003=300

PD004=300

PD005=300

PD006=90

PD007=20

PD008=220

PD009=66

PD010=15

PD011=120 ( This may need to have a higher Minimum Speed for your Spindle watch Temperature )

PD13= 08 is for Factory reset, Only use this to set VFD to Factory Default Settings

PD014=10 ( Acceleration Adjust to suit)

PD015=10 (Deceleration Adjust to suit)

PD141=220 ( Motor Rated Voltage )

PD142=9 ( Motor Max Amps)

PD143=2 ( Motor Number of Poles)

PD144=3000 (Max Motor RPM 18,000)

PD070=0 ( This may need to be set to 1 if Control Voltage is 0-5v )

PD072=300

PD073=120 ( This may need to have a higher Minimum Speed for your Spindle watch Temperature )

PD120=120 (Stall Prevention )

PD174=13 ( Your VFD Drives Max Amp Output Rating )


If Minimum Speed is changed then other Parameters will need to be changed also, Your Minimum Speed is related to the temperature of your Spindle to low and it will over heat