3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?


Results 1 to 7 of 7

Thread: 3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?

  1. #1
    Member
    Join Date
    Oct 2006
    Location
    Canada
    Posts
    21
    Downloads
    0
    Uploads
    0

    Default 3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?

    So I ordered this set-up from Amazon.ca. Came in looked good. Finally over the Christmas break I hooked it up on my CamTech CNC router. I replaced a Freud2000 3.25hp plunge router. Now the test. I put in my 2" flattening bit into the ER20 collet and clamped down a piece of hard maple. I wanted to take a full 2" wide cut at 0.1" deep. Hand jogged into the wood at about 60ipm. The spindle just stalled. I know my Freud router would have done the cut. So did I just buy a weak spindle? Let me know what you guys think.

    Thanks

    Kevin

    Similar Threads:


  2. #2
    Community Moderator Al_The_Man's Avatar
    Join Date
    Dec 2003
    Location
    Canada
    Posts
    23638
    Downloads
    0
    Uploads
    0

    Default Re: 3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?

    Is it set for V/Hz or as is should be, Sensor-less vector mode?
    Al.

    CNC, Mechatronics Integration and Custom Machine Design

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.


  3. #3
    Member
    Join Date
    Oct 2006
    Location
    Canada
    Posts
    21
    Downloads
    0
    Uploads
    0

    Default Re: 3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?

    Hi AL,

    Not sure i understand your question. I have only played with a few settings in the VFD

    would you know what PD it would be?



  4. #4
    Member
    Join Date
    Oct 2006
    Location
    Canada
    Posts
    21
    Downloads
    0
    Uploads
    0

    Default Re: 3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?

    Ok so did some more reading I understand what I have to do now I just cannot find where to switch my VFD to sensorless vector mode

    I have a hy03d023b looking through the manual this evening



  5. #5
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    12087
    Downloads
    0
    Uploads
    0

    Default Re: 3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?

    Quote Originally Posted by V8 BUG View Post
    Ok so did some more reading I understand what I have to do now I just cannot find where to switch my VFD to sensorless vector mode

    I have a hy03d023b looking through the manual this evening
    The standard Huanyang is not a vector control VFD Drive and most Vector control drives do do not work for these 400Hz spindles so would not make any difference if you had it or not

    A 2" cutter is a tall order for any spindle what Parameters have you set ??

    What RPM where you running at ??

    Mactec54


  6. #6
    Member
    Join Date
    Oct 2006
    Location
    Canada
    Posts
    21
    Downloads
    0
    Uploads
    0

    Default Re: 3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?

    Hi Mactec54,

    I have tried at full rpm as well as from 50% up. I did make some changes to pd145(auto torque compensation) and pd147(motor slip compensation).

    With these 2 set to about 75% i can cut the full width 2" @ .1 dp. but only at about 60ipm.

    Doing a test now with a V-carve to see how it handles that...but i don't think it will have a problem with it.

    I have until Jan 31, 2021 to return the VFD or spindle. Not sure I won't yet as i feel a good wood router will be stronger.



  7. #7
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    12087
    Downloads
    0
    Uploads
    0

    Default Re: 3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?

    Quote Originally Posted by V8 BUG View Post
    Hi Mactec54,

    I have tried at full rpm as well as from 50% up. I did make some changes to pd145(auto torque compensation) and pd147(motor slip compensation).

    With these 2 set to about 75% i can cut the full width 2" @ .1 dp. but only at about 60ipm.

    Doing a test now with a V-carve to see how it handles that...but i don't think it will have a problem with it.

    I have until Jan 31, 2021 to return the VFD or spindle. Not sure I won't yet as i feel a good wood router will be stronger.
    A good wood router is not even close

    That is why I asked what Parameters you have set, as this is important if they are not set correct you will damage the VFD Drive or the spindle, and that won't be the fault of who you brought it from

    Mactec54


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?

3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?

3kw Air Cooled spindle with Huanyang VFD...am I expecting too much?