VFD HY 2.2kw 220v wiring to UB1 Controller Help

[akihiko]

Hello, all

Need some help to setup VFD to UC300ETH-UB1.

Read both manual for UB1 and VFD HY. not much on how to setup wiring.. Most of the information i got from reference on YouTube.

On my diagram hive following wiring set, except the last wire (AH1), which im not sure where it go.

On the VFD pin 1,2 are jump for external connection.

From VFD DCM+FOR connected to UB1 on ON/CM1 relay

The other configuration came up with:

AL1---> VFD---> ACM
AO1--> VFD---> AL
AH1--> VFD---> not sure

If anyone can help me connect this right way., So i don't end up doing damageto VFD or UB1.

Appreciate all the help i can get...



And to everyone be safe out there.

Similar Threads:

• Need Help!- 220v vfd wiring
• Newbie- Wiring 3P 380v or 1P 220v
• Wiring for Huanyang 220V 2.2kw VFD...NEED HELP PLEASE!
• Need Help!- Converted CNC Bench top Lathe Motor Wiring Issue - Brazil 220V to US 220V
• Need Help!- VFD Wiring from 220v Converter

[ger21]

UB1 --- VFD
AH1 --- +10
AO1 --- VI
AL1 --- ACM

[akihiko]

Thanks so much

[akihiko]

Need help with the VFD Parameters.

when i type M3 24000, spindel dosen't move, when i go back to jump VR spindle works fine...

Jump on V1

My parameters in VFD

PD001=1

PD002=1

PD003=400

PD004=400

PD005=400

PD008=220

PD013=00

PD044=1 to use FOR

PD070=? SET FACTORY 0 <---?

PD072=400

PD141=220

PD144=24000


Screenshot of uccnc spidle setting..

[ger21]

when i type M3 24000, spindel dosen't move

Try:
S24000
M3

[akihiko]

didn't work

[akihiko]

So i double checked the parameters my VFD HY 220 2.2kw

My spindle is:

GDZ-80-2 2B
220V 2.2KW 8A
400Hz 24000rpm


VFD parametters

PD000=0
PD001=1
PD002=1
PD003=400
PD004=400
PD005=400
PD007=.50
PD008=220
PD009=13.0
PD010=6.5
PD011=00.0
PD013=00
PD014=20.0
PD015=20.0
PD044=1
PD070=
PD072=400
PD073=0.00
PD141=220
PD142=11.0
PD144=3000

On UCCNC spindle screen, What port is AL1,AO1,AH1 connected too?

[mactec54]

So i double checked the parameters my VFD HY 220 2.2kw

My spindle is:

GDZ-80-2 2B
220V 2.2KW 8A
400Hz 24000rpm


VFD parametters

PD000=0
PD001=1
PD002=1
PD003=400
PD004=400
PD005=400
PD007=.50
PD008=220
PD009=13.0
PD010=6.5
PD011=00.0
PD013=00
PD014=20.0
PD015=20.0
PD044=1
PD070=
PD072=400
PD073=0.00
PD141=220
PD142=11.0
PD144=3000

On UCCNC spindle screen, What port is AL1,AO1,AH1 connected too?

Yes PD070=0 for 0-10v control ( 1 ) for Pot control

PD011=100
PD073=100

[akihiko]

thanks, after the two changes made in VFD parameters below

PD011=100
PD073=100

key in M3 , but run at only 100 slow, make noises


check video uploaded youtube:




help.

[ger21]

On UCCNC spindle screen, What port is AL1,AO1,AH1 connected too?

Port 4 pin 1, as shown on page 24 of the UB1 manual.

[akihiko]

hey, ger21

can you help get VFD up and running..

VFD parametters

PD000=0
PD001=1
PD002=1
PD003=400
PD004=400
PD005=400
PD007= 20
PD008=220
PD009=15
PD010=8
PD011=120.0
PD013=00
PD014=12
PD015=12
PD044=1
PD070=0
PD072=400
PD073=120.0
PD141=220
PD142=8.5
PD144=3000

when M3 spindle start, but run at 120,

when type 2400 it run at 100.


if over post, you see picture's /video/ wiring from VFD to UB1.

im hiving a hard time it.


thanks

[ger21]

PD072=400
PD073=120.0

You have these backwards

PD072 = 120
PD073 = 400

You also have it wired wrong.
Move the wire from AI to VI.

Measure the voltage between ACM and VI at different speeds. You should get 5V at 12000 rpm, and about 9.8V at 24000 rpm.

If you don't, measure the voltage on the UB1 between AO1 and AL1. You should be seeing the same voltages.

[mactec54]

You have these backwards

PD072 = 120
PD073 = 400

You are confused the Parameters are correct

[mactec54]

thanks, after the two changes made in VFD parameters below

PD011=100
PD073=100

key in M3 , but run at only 100 slow, make noises


check video uploaded youtube:




help.

Wiring is incorrect

100Hz =6,000 RPM 120Hz = 7,200 RPM

[ger21]

You are confused the Parameters are correct

The manual I have is wrong. It shows them both ways in different places. Sorry for the mistake.

[akihiko]

Which wiring?

[akihiko]

Wiring is incorrect

100Hz =6,000 RPM 120Hz = 7,200 RPM

Which wiring?

the wiring from UB1 to VFD.

AL1 ---> to VFD ---> ACM
AO1 --> to VFD ---> AI
AH1 --> to VFD ---> 10V

or

VFD and Spindle is working fine,

When change PD001 & PD002 back to 0, Operator mode.

The spindle run 0 to 400hz with no problem. i double check the wiring to spindle.

VFD --> Spindle

U --> pin 2
V --> pin 1
W --> pin 3
G --> pin 4 is wire, but not use at this time.

[ger21]

As I said before, move the wire from AI to VI.
AI is for current, VI is for 0-10V

[mactec54]

Which wiring?

the wiring from UB1 to VFD.

AL1 ---> to VFD ---> ACM
AO1 --> to VFD ---> AI
AH1 --> to VFD ---> 10V

or

VFD and Spindle is working fine,

When change PD001 & PD002 back to 0, Operator mode.

The spindle run 0 to 400hz with no problem. i double check the wiring to spindle.

VFD --> Spindle

U --> pin 2
V --> pin 1
W --> pin 3
G --> pin 4 is wire, but not use at this time.

As Gerry has said VFD wiring is incorrect just one change VFD ---> VI and to check that you have 0-10v from the control when you make a speed change 5v = around 12000 Rpm so in MDI M3S12000 and check the voltage output before you run the spindle, yo must have the output voltage working before you connect to the spindle

Normally the wiring for the spindle is

Input wiring R T and Ground Terminals

U=Pin 1
V=Pin 2
W=Pin 3
Ground Pin 4

[akihiko]

As Gerry has said VFD wiring is incorrect just one change VFD ---> VI and to check that you have 0-10v from the control when you make a speed change 5v = around 12000 Rpm so in MDI M3S12000 and check the voltage output before you run the spindle, yo must have the output voltage working before you connect to the spindle

Normally the wiring for the spindle is

Input wiring R T and Ground Terminals

U=Pin 1
V=Pin 2
W=Pin 3
Ground Pin 4

The output AH1 is 5v to 10v


it working now.
M3 run @ 12000 & S24000
i check all my wiring all good.


One question, about stepper driver and setting..

Stepper Drive DM542A and the DIP switch setting
sw1=on , sw2=on , sw3=off = Peak-> 2.84 / RMS->2.03
sw4=off --> Half current
sw5=off , sw6=off , sw7=on , sw8=on -->1600

Stepper motor:
57HD6401-14S 1.8` 3A N1905

The reason im asking is because my AXIS sound a little rough. X, Y, Z,

A picture of UB1 AXIS setting..

maybe i need turn them?



thanks for all the help on the VFD & Spindle guys