Need Help! Break HF spindle with breaking resistor?


Results 1 to 5 of 5

Thread: Break HF spindle with breaking resistor?

  1. #1
    Member
    Join Date
    Dec 2006
    Location
    Sweden
    Posts
    74
    Downloads
    0
    Uploads
    0

    Default Break HF spindle with breaking resistor?

    Hello,
    I am trying to break a 3kw 24000rpm 800hz spindle motor with a vfd and breaking resistor but the breaking resistor does not do much good, it takes about 10s to stop the spindle both with and without resistor.
    The only difference is that with the resistor the vfd does not report an error of over voltage during breaking so apparently its working somewhat.
    We have tried from 25ohm to 150ohm without any aparent difference.

    Could it be that the high frequency does not work well with the resistors? that the impendance in the resistor is to high to work with high frequencies?

    The VFD counts down to zero in 1-2s or whatever I set the decceleration parameter to and then the breaking resistor slowly break the motor to zero.

    Similar Threads:


  2. #2
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    11127
    Downloads
    0
    Uploads
    0

    Default Re: Break HF spindle with breaking resistor?

    Quote Originally Posted by jeeybee View Post
    Hello,
    I am trying to break a 3kw 24000rpm 800hz spindle motor with a vfd and breaking resistor but the breaking resistor does not do much good, it takes about 10s to stop the spindle both with and without resistor.
    The only difference is that with the resistor the vfd does not report an error of over voltage during breaking so apparently its working somewhat.
    We have tried from 25ohm to 150ohm without any aparent difference.

    Could it be that the high frequency does not work well with the resistors? that the impendance in the resistor is to high to work with high frequencies?

    The VFD counts down to zero in 1-2s or whatever I set the decceleration parameter to and then the breaking resistor slowly break the motor to zero.
    What VFD Drive do you have

    Mactec54


  3. #3
    Member
    Join Date
    Dec 2006
    Location
    Sweden
    Posts
    74
    Downloads
    0
    Uploads
    0

    Default Re: Break HF spindle with breaking resistor?

    Hello,
    Its a Machtric Z900 400v 2.2kw



  4. #4
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    11127
    Downloads
    0
    Uploads
    0

    Default Re: Break HF spindle with breaking resistor?

    Quote Originally Posted by jeeybee View Post
    Hello,
    Its a Machtric Z900 400v 2.2kw
    There is a new VFD listed everyday I would say you don't have the Braking Parameters setup correct the normal without a Braking Resistor is around 3 to 5 sec for that spindle

    So your spindle is 4 Pole ??

    Mactec54


  5. #5
    Member
    Join Date
    Dec 2006
    Location
    Sweden
    Posts
    74
    Downloads
    0
    Uploads
    0

    Default Re: Break HF spindle with breaking resistor?

    Quote Originally Posted by mactec54 View Post
    There is a new VFD listed everyday I would say you don't have the Braking Parameters setup correct the normal without a Braking Resistor is around 3 to 5 sec for that spindle

    So your spindle is 4 Pole ??
    Yes it is.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Break HF spindle with breaking resistor?

Break HF spindle with breaking resistor?

Break HF spindle with breaking resistor?