Huanyang VFD HY01D511B potentiometer issue


Results 1 to 9 of 9

Thread: Huanyang VFD HY01D511B potentiometer issue

  1. #1
    Member
    Join Date
    Jan 2011
    Location
    Canada
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Huanyang VFD HY01D511B potentiometer issue

    Hi

    I have a Huanyang VFD HY01D511B 110V 1.5kw, and when I turn it on, the potentiometer display turns on as usual and when I press the run key,
    the spindle start until it reach the maximum speed, without turning the speed knob of the potentiometer wich remain at zero. (seems disable).

    I had previously program VFD PD.... according to instructions obtained from Mactec54 post



    "This is all you need, all the basic Parameter Settings are the same for all the 400Hz Spindles, just voltage and Amps that are different

    Don't do a Reset unless you have to, sometimes doing this affects the order of how the Parameters get set

    " Huanyang Mactec54

    PD000=0 for Parameter unlock ( 1 ) for Parameter Lock

    PD001=0 (1 For Remote Control)

    PD002=0 ( 1 For 0-10v Terminal Control or Remote Trim Pot Control )
    ( J1 Also Needs to be set for Terminal Control )

    PD003=400

    PD004=400

    PD005=400

    PD007=20

    PD008=220 (120 If you have 120v VFD )

    PD009=15

    PD010=8

    PD011=120 ( 100 Minimum Setting with Quality VFD, 120 is Safe)

    PD13= 08 is for Factory reset, Only use this to set VFD to Factory Default Settings

    PD014 Acceleration=12 ( Adjust to suit)


    PD015 Deceleration=12 (Adjust to suit)

    ( PD15 is ignored IF PD26=1 Then the Spindle will Coast to a Stop)

    PD141=220 ( Motor Rated Voltage ) (120 for VFD Rated for 120v )

    PD142= ( Motor Max Amps)

    PD142=( 220vSet for your motor Amp Rating 2.2Kw Spindle 9 amp )
    PD142=( 220VSet for your motor Amp Rating 1.5Kw Spindle 7 amp )
    PD142=( 220v Set for your motor Amps Rating 800w Spindle 4 amps )
    PD142=( 120v Set for your motor Amp Rating 800w Spindle 7 amp )

    PD143=2 ( Motor Number of Poles)

    PD144=3000 (Max Motor RPM) =3,000= (24,000)

    PD70=0 ( This may need to be set to 1 if Control Voltage is 0-5v )

    PD72=400

    PD73=120 ( 100 Minimum Setting )"



    Does anyone have an idea of the problem ? Should I do something with the J1 jumper ?

    Thank you

    Jack


    Attachment 430160Huanyang VFD HY01D511B potentiometer issue-img_0415-2-jpg

    Similar Threads:
    Last edited by JackMath; 10-27-2019 at 11:52 AM.


  2. #2
    Member
    Join Date
    Jan 2011
    Location
    Canada
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang VFD HY01D511B potentiometer issue

    Hi

    Problem Fixed


    Here is the change I've made in my parameters:



    PD002 was change from 0 to 1
    PD070 was change from 0 to 1

    I tried to change them before but not both simultaneously.......without success

    Thank you

    Jack



  3. #3
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang VFD HY01D511B potentiometer issue

    Quote Originally Posted by JackMath View Post
    Hi

    Problem Fixed


    Here is the change I've made in my parameters:



    PD002 was change from 0 to 1
    PD070 was change from 0 to 1

    I tried to change them before but not both simultaneously.......without success

    Thank you

    Jack
    Yes that is the fix for pot use on some of these VFD Drives as per what is written beside each of the Parameters in the list you posted, there is always a possibility that they may need to be changed depending on the operation you are wanting to do with the KeyPad

    Sometimes you need to change the J1 Jumper also

    Mactec54


  4. #4
    Member
    Join Date
    Jan 2011
    Location
    Canada
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang VFD HY01D511B potentiometer issue

    Quote Originally Posted by mactec54 View Post
    Yes that is the fix for pot use on some of these VFD Drives as per what is written beside each of the Parameters in the list you posted, there is always a possibility that they may need to be changed depending on the operation you are wanting to do with the KeyPad

    Sometimes you need to change the J1 Jumper also

    Thank you Mactec54

    I often hear about jumper j1 but I have not yet spotted it, could it be that in my case it is the jumper V1 / VR as in the photo attached ?

    Jack


    Huanyang VFD HY01D511B potentiometer issue-img_0421-jpg



  5. #5
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang VFD HY01D511B potentiometer issue

    Quote Originally Posted by JackMath View Post
    Thank you Mactec54

    I often hear about jumper j1 but I have not yet spotted it, could it be that in my case it is the jumper V1 / VR as in the photo attached ?

    Jack


    Huanyang VFD HY01D511B potentiometer issue-img_0421-jpg
    That is the normal location of the Jumper for remote use

    Do you have a PDF manual that you could post here of your drive, I have seen V1 / VR before would like to see what is in the manual

    Mactec54


  6. #6
    Member
    Join Date
    Jan 2011
    Location
    Canada
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang VFD HY01D511B potentiometer issue

    Quote Originally Posted by mactec54 View Post
    That is the normal location of the Jumper for remote use

    Do you have a PDF manual that you could post here of your drive, I have seen V1 / VR before would like to see what is in the manual

    no pdf but manual page as per photo attached regarding V1-VR jumper wich appears to be the same as jumper J1

    In my case, I left the jumper as shipped by the factory, position 2 and 3 and it work fine.

    jack


    Huanyang VFD HY01D511B potentiometer issue-capture-d-cran-20-jpg

    Huanyang VFD HY01D511B potentiometer issue-img_0423-jpg

    Last edited by JackMath; 10-30-2019 at 02:04 PM.


  7. #7
    Member
    Join Date
    Jan 2011
    Location
    Canada
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang VFD HY01D511B potentiometer issue

    Quote Originally Posted by mactec54 View Post
    That is the normal location of the Jumper for remote use

    Do you have a PDF manual that you could post here of your drive, I have seen V1 / VR before would like to see what is in the manual

    no pdf but manual page as per photo attached regarding V1-VR jumper wich appears to be the same as jumper J1

    In my case, I left the jumper as shipped by the factory, position 2 and 3 and it work fine.

    jack


    Huanyang VFD HY01D511B potentiometer issue-capture-d-cran-20-jpg



  8. #8
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang VFD HY01D511B potentiometer issue

    Quote Originally Posted by JackMath View Post
    no pdf but manual page as per photo attached regarding V1-VR jumper wich appears to be the same as jumper J1

    In my case, I left the jumper as shipped by the factory, position 2 and 3 and it work fine.

    jack


    Huanyang VFD HY01D511B potentiometer issue-capture-d-cran-20-jpg
    Are they are still calling it a J1 that's important as I thought by your post it may have changed how it was used, but it is the same just giving the jumper positions a name VI and VR

    Mactec54


  9. #9
    Member
    Join Date
    Jan 2011
    Location
    Canada
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang VFD HY01D511B potentiometer issue

    Yes they are still calling it J1 (with subtitle V1-VR) as you can see here in a closeup picture attached


    Huanyang VFD HY01D511B potentiometer issue-img_0423-jpg



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Huanyang VFD HY01D511B potentiometer issue

Huanyang VFD HY01D511B potentiometer issue