VFD manual for MK100-2S2.2G-DK

[Ktmben]

Does anyone have the manual for VFD manual for MK100-2S2.2G-DK

Have attached pic of the manufacturer plate

Thanks

Similar Threads:

• Need Help!- I will buy CNC swiss type Tsugami S25D but no have manual.I need manual of machine.
• Need Help!- Daewoo Puma 10s user manual and fanuc control system technical manual
• For Sale Complete Maho MH 600E Manual, + Philips 432 Programming Manual
• Need Help!- Mecof CS100 manual & Zayer KM 8000 manual
• Wanted maintenance manual B-62175E and spindle manual B-65045E

[wmgeorge]

Does anyone have the manual for VFD manual for MK100-2S2.2G-DK

Have attached pic of the manufacturer plate

Thanks

No picture and why do you folks by these drives without documentation?? Asking your Chinese vender would be the first place I would try.

[mactec54]

Does anyone have the manual for VFD manual for MK100-2S2.2G-DK

Have attached pic of the manufacturer plate

Thanks

So you have a CNC Control Panel with an open board VFD Drive there is a thread for these control boxes under 6040 I have some of there manuals but may not have your one you will need more information and take some photos of what you have inside the cabinet / box

[Crossfixer]

Does anyone have the manual for VFD manual for MK100-2S2.2G-DK

Have attached pic of the manufacturer plate

Thanks

Here is the manual you wanted.

https://1drv.ms/b/s!AlWEvfzVs336oREF9zNq6qcxH5kF

[Abersmith]

This saved the day for me cheers for the manual. Which setting if to allow Mach 3 to control the spindle speed?

[Iron_Geek_37]

This saved the day for me cheers for the manual. Which setting if to allow Mach 3 to control the spindle speed?

Did you ever figure this out? I have a machine with the same VFD and I can't seem to get mach3 to control the spindle.

[laurent28200]

Hello,
I have a CNC6040Z S80 with a MK100-2S2.2G-DK in the black box.
In the manual there is no info about RS485 / Modbus protocol...

I have modified:
P0-02 to 2 for communication command channel
P0-03 to 9 for communication command for frequency control

Modbus rtu request:
with 01 06 20 00 00 01 I can RUN
with 01 06 20 00 00 05 I can STOP

But
with 01 06 20 01 0F A0 i can't modify frequency.

Did I miss something ?
or Have you modbus documentation

thanks a lot
Laurent
excuse my english i'm french

[raindancer2204]

Hi,

i have a question for the frequency inverter MK100-2S1.5G-DK. I want to start my Spindle via CNC Software. My CNC6040 is from the Vendor "SXCNC".
Has anyone ever wired the frequency inverter to the mainboard JP-3163B?

Can you have a look to my Post here i worte all in details about my question?

https://www.cnczone.com/forums/chine...ml#post2402392

Regards Raini

[dontworry21]

Hi a buy an chinazone CNC 3040Z-DQ 4-axis Router 800W Engraving Mach 3 USB Cutting Engraver Machine on ebay a while ago and havent been able to do anyting with it until now so a have done everything clear to start up the machine and try it out and check if stepper motors and spindel runs as it shud do, and a so far a have get the stepper motors to run ,but not the spindel motor?
a have been looking all over to find help how to setup my VFD so the spindel start runing.
a did not find any macth on the VFD controler panel anywhere a have looked so a desided to open it up and se innside to find out wicth VFD it had and find out that it is an MK100-2S1.5G-DK so there was an other question poping up??this is an VFD to 1.5kW spindel motor and the spindel a got is an 800W spindel motor eehh ok???
Is that a problem??or can it be fixed changeing the parameters on the VFD to fit the 800w spindel??
my software is Mach3 running on windows10,there is an mainboard MKS4-V in the controller box.
so can anyone her help me how to setup this VFD to getting the 800w spindel start running on mach3? how this is done step by step with the VDF?
And how to setup the end limit switches to functions proporly?
A have been very happy to get some help getting this machine up and running

thx dontworry21