Huanyang Chinese VFD settings and manual here!

[mactec54]

Thanks for the info!
can you elaborate on the reset (RST) part?
My understanding is the RST is an input to reset the VFD after a fault.
I'm looking for an output from the VFD when there is a fault. to Estop my Mach3 run CNC Mill.




Thanks
Glen

They are all switches that are either open or closed just like FWD and DCM ( 1 ) of the Relays is what most use for there safety circuit and is the easiest to use RST is also just a switch

[Pasticciere]

hi, does anyone know this damn inverter ?? aesthetically it is similar to the others, but it has a different menu. I have the spindle that heats up a lot in a few minutes. is a 1.5kw air-cooled spindle and the inverter is this:
http://www.et.byu.edu/~sorensen/A2%20VFD%20Manual.pdf
I just can't set it ... can someone explain to me why the menu is different from the usual vfd?
Thanks to anyone who wants to help me. I apologize for English, but I am using the google translator, because I am an Italian donkey. : D

[Geoff Sims]

Hi

I recently bought a replacement 2.2kw HY02D223B vfd and have set it up on my cnc machine running an air cooled spindle. No matter what I do, I cannot get the front panel potentiometer to work. I don't need remote control at all and am happy to just use the pot on the front of the vfd, but I cannot get it to work. The spindle is working fine and I have been through this post and triple checked all the pd settings which are exactly the same as those on my old vfd. That one worked but this one doesn't.

I must be doing something wrong but I don't know what and just got myself confused. It's very difficult not being able to adjust the speed of the spindle.

I've left it for quite a while and am ready to tackle it again afresh.

Any helpful suggestions please?

Cheers

[gfacer]

Had you tired the jumper to the side of all the input terminals?

I had the opposite problem, trying to control remotely, and that was the issue.

Cheers

Sent from my motorola one using Tapatalk

[Geoff Sims]

Had you tired the jumper to the side of all the input terminals?

I had the opposite problem, trying to control remotely, and that was the issue.

Cheers

Sent from my motorola one using Tapatalk

Yes, I've tried with the jumper in both positions but to no avail.

[gfacer]

Yes, I've tried with the jumper in both positions but to no avail.

I assume you have also flipped the external control program setting both ways too?

Sent from my motorola one using Tapatalk

[mactec54]

Hi

I recently bought a replacement 2.2kw HY02D223B vfd and have set it up on my cnc machine running an air cooled spindle. No matter what I do, I cannot get the front panel potentiometer to work. I don't need remote control at all and am happy to just use the pot on the front of the vfd, but I cannot get it to work. The spindle is working fine and I have been through this post and triple checked all the pd settings which are exactly the same as those on my old vfd. That one worked but this one doesn't.

I must be doing something wrong but I don't know what and just got myself confused. It's very difficult not being able to adjust the speed of the spindle.

I've left it for quite a while and am ready to tackle it again afresh.

Any helpful suggestions please?

Cheers

Can be tricky as everything has to be correct to make the Pot work, If you are using remote control you will not have any Pot Control no matter what you do, Pot Control is only active if in KeyPad mode

Pot Control
PD001=0

PD002=1

PD070=1

JI Jumper 2-3 Position this may be labeled different on your model

[Geoff Sims]

Can be tricky as everything has to be correct to make the Pot work, If you are using remote control you will not have any Pot Control no matter what you do, Pot Control is only active if in KeyPad mode

Pot Control
PD001=0

PD002=1

PD070=1

JI Jumper 2-3 Position this may be labeled different on your model

Thank you Mactec54.

I went in and checked those settings and they were correct. I also went in and checked PD072 & 73 as I have read somewhere that they can sometimes be reversed, so I changed them. Didn't work, so I changed them back to the original values and MAGIC!

Everything now works as it should, and I am a happy fella. Don't know what changed because, as far as I know, everything is as it was before I touched it this morning. I think the software on these things is very flaky but it works now so I don't care

[mactec54]

Thank you Mactec54.

I went in and checked those settings and they were correct. I also went in and checked PD072 & 73 as I have read somewhere that they can sometimes be reversed, so I changed them. Didn't work, so I changed them back to the original values and MAGIC!

Everything now works as it should, and I am a happy fella. Don't know what changed because, as far as I know, everything is as it was before I touched it this morning. I think the software on these things is very flaky but it works now so I don't care

PD072 and PD073 these 2 Parameters set reversed will cause a problem, and no they can't be used or set in reverse not in any circumstances

[jojo77]

Hi. I have my vfd hooked up to centroid acorn and it’s up and running. I can get it to go in forward or reverse and have run a few test jobs. But setting the spindle speed in the acorn software doesn’t change anything. It only goes full speed. And messing with the knob doesn’t have any effect either. Any ideas would help. Thank you!

[mactec54]

Hi. I have my vfd hooked up to centroid acorn and it’s up and running. I can get it to go in forward or reverse and have run a few test jobs. But setting the spindle speed in the acorn software doesn’t change anything. It only goes full speed. And messing with the knob doesn’t have any effect either. Any ideas would help. Thank you!

First you will have to test the output from your control to see if it is changing the voltage when you do a speed change M3S12000, you did not say what your spindle max RPM is, so need more information

[jojo77]

First you will have to test the output from your control to see if it is changing the voltage when you do a speed change M3S12000, you did not say what your spindle max RPM is, so need more information

I’ll test the output to make sure it’s 1-10v. The max speed on the spindle is 24k

[jojo77]

First you will have to test the output from your control to see if it is changing the voltage when you do a speed change M3S12000, you did not say what your spindle max RPM is, so need more information

Also my vfd has the little jumper things labeled VI & VR. It currently has the clip on it so it’s set to VR (connecting the two right pieces). Should it be set to the left (VI)?? The knob doesn’t do anything when I try to adjust the speed. But of course I want to set speeds in the acorn software not the knob

[mactec54]

Also my vfd has the little jumper things labeled VI & VR. It currently has the clip on it so it’s set to VR (connecting the two right pieces). Should it be set to the left (VI)?? The knob doesn’t do anything when I try to adjust the speed. But of course I want to set speeds in the acorn software not the knob

To make it easier you need to have it all running with out the control connected then you can move to connecting to the control

Pot Control
PD001=0

PD002=1

PD070=1

JI Jumper Pin 2-3 / VR Position this is normal connection, some need it connected to the VI

[jojo77]

To make it easier you need to have it all running with out the control connected then you can move to connecting to the control

Pot Control
PD001=0

PD002=1

PD070=1

JI Jumper Pin 2-3 / VR Position this is normal connection, some need it connected to the VI

I appreciate your help. I had it running without the controller using a list of settings that I believe originated from you in this thread. Not sure if or where I took a wrong turn. So the settings put here are to get it back to pot/knob control?

[mactec54]

I appreciate your help. I had it running without the controller using a list of settings that I believe originated from you in this thread. Not sure if or where I took a wrong turn. So the settings put here are to get it back to pot/knob control?

Yes this should get you to be able to use it with the Pot sometimes the PD002 needs to be ( 0 ) also there are some of these VFD Drives that have some Parameter that are different but normally there is only one or two that are different, the J1 Jumper can also be change as it can be backwards as well

You need every thing working with the VFD Drive before you connect for remote control

And yes I know and understand you want to connect to the Acorn

So you need to check with a meter that the Acorn output Voltage is changing 0-10v so in MDI mode M3S12000 and the voltage should be around 5v if you have the Acorn setup 10v would be 24000 so test this part as well before connecting to the VFD Drive

[jojo77]

Yes this should get you to be able to use it with the Pot sometimes the PD002 needs to be ( 0 ) also there are some of these VFD Drives that have some Parameter that are different but normally there is only one or two that are different, the J1 Jumper can also be change as it can be backwards as well

You need every thing working with the VFD Drive before you connect for remote control

And yes I know and understand you want to connect to the Acorn

So you need to check with a meter that the Acorn output Voltage is changing 0-10v so in MDI mode M3S12000 and the voltage should be around 5v if you have the Acorn setup 10v would be 24000 so test this part as well before connecting to the VFD Drive

Thank you for your help. I’ll give this a try.

[jojo77]

Yes this should get you to be able to use it with the Pot sometimes the PD002 needs to be ( 0 ) also there are some of these VFD Drives that have some Parameter that are different but normally there is only one or two that are different, the J1 Jumper can also be change as it can be backwards as well

You need every thing working with the VFD Drive before you connect for remote control

And yes I know and understand you want to connect to the Acorn

So you need to check with a meter that the Acorn output Voltage is changing 0-10v so in MDI mode M3S12000 and the voltage should be around 5v if you have the Acorn setup 10v would be 24000 so test this part as well before connecting to the VFD Drive

Hi mactec, I changed the program like you suggested for pot control and it works as expected (speed adjusts with the dial). I also tested the output in acorn m3s24000 gives 10v reading on the multi meter. M3s12000 gives 5v and so on. Once I hooked up the vfd with acorn the results are not what I expected.

See below for mdi setting versus readout on the vfd.
M3S3000 : 9367
M3S6000: 11,500
M3S12000: 15,750
M3S18000: 20,000
M3S24000: 24000 (I expected this value since it’s max)

Do you think this is an issue with acorn set up or on the vfd?

[mactec54]

Hi mactec, I changed the program like you suggested for pot control and it works as expected (speed adjusts with the dial). I also tested the output in acorn m3s24000 gives 10v reading on the multi meter. M3s12000 gives 5v and so on. Once I hooked up the vfd with acorn the results are not what I expected.

See below for mdi setting versus readout on the vfd.
M3S3000 : 9367
M3S6000: 11,500
M3S12000: 15,750
M3S18000: 20,000
M3S24000: 24000 (I expected this value since it’s max)

Do you think this is an issue with acorn set up or on the vfd?

Unless your spindle is rated for 3000 RPM which only a few models are you have the Parameters in you VFD Drive set incorrect, if your spindle is water cooled 24,000 RPM you have a minimum speed of 6000 RPM your control software also has to be set to match your spindle speeds or it won't be able to give you the correct voltage to speed ratio

[Mofireman]

Legitimately have a headache guys! Been working on this all day long. I have the HuanYang manual, but it's like reading Chinese (joke intended) sometimes.

Main problem is I keep getting an overcurrent error (EoC-A). Here are my components...

Spindle:
HuanYang GDZ-80-2.2A
110volt; 2.2kw
400Jz; 24,000 rpm

VFD:
HY02D211B
Input- 110 +/- 20%
Output- 3PH 0-110AC. 2.2kw. 0.5-400Hz

I just wired up a new electrical connector this morning, and now it seems that I may have a wire crossed or coming into contact with something else?! I've reset the factory settings and set new parameters, but the overcurrent continues. With the dial turned all the way down, I can hit "Run" and as soon as I start to rotate the dial, I hear a click and the error code pops up.

Sincerely appreciate any help!!