Huanyang Chinese VFD settings and manual here! - Page 4


Page 4 of 41 FirstFirst 123456714 ... LastLast
Results 61 to 80 of 808

Thread: Huanyang Chinese VFD settings and manual here!

  1. #61
    Registered
    Join Date
    May 2003
    Location
    Port Orange, Fl
    Posts
    132
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    60 X Hz = rpm
    60 X 300 = 18000 RPM
    60 X 400 + 24000 RPM
    you should be putting out 18000 RPM. Hope this helps
    Donald Clifton



  2. #62
    Registered
    Join Date
    Apr 2011
    Location
    USA
    Posts
    31
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by Don C View Post
    60 X Hz = rpm
    60 X 300 = 18000 RPM
    60 X 400 + 24000 RPM
    you should be putting out 18000 RPM. Hope this helps
    Donald Clifton
    Hello Donald. Yes, I'm fairly certain it's putting out 300hz as the VFD shows, however the issue is rott on the VFD doesn't read 18000. It was my understanding that it could/should read 18000. Am I mistaken?



  3. #63
    Registered
    Join Date
    Apr 2011
    Location
    USA
    Posts
    31
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by mactec54 View Post
    btsioles

    Have not done an 18,000RPM with this spindle, so if you were getting to 300Hz then you were at max speed, It would be wise to use the settings you had put in, obvious the seller is just that & does not know how to set the drive up

    You have an air cooled spindle so it is very important, that you have the minimum speed set correct, 120 Hz will be to low, looking at the photos, they are saying that your spindle is 400 Hz with a minimum of 300Hz
    Thanks for the reply. I'm confused. The spindle says 300Hz. Where do you see it's 400 Hz? I should set PD011 TO 300? Why are others using 120?



  4. #64
    Registered Dytoven's Avatar
    Join Date
    Apr 2015
    Posts
    17
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    I have the same products with some small variation as you can see in the picture.

    The problem is PD070, switch 0 to 1

    With this configuration after factory reset works perfectly, tested with a laser tachometer.

    PD001 - 0
    PD002 - 1 (Board Potentiometer, you leave it at 0)
    PD003 - 300
    PD004 - 300
    PD005 - 300
    PD009 - 15
    PD010 - 8
    PD070 - 1
    PD072 - 300
    PD141 - 220
    PD142 - 8.6
    PD143 - 2
    PD144 - 3000

    If you have other voltage in your house, just change the parameters 220 to x.



  5. #65
    Registered
    Join Date
    May 2003
    Location
    Port Orange, Fl
    Posts
    132
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    I'm not sure but one of the buttons should scroll thur hz, rpm, amps.
    Don



  6. #66
    Registered
    Join Date
    Apr 2011
    Location
    USA
    Posts
    31
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Great thanks Dytoven. What about PD011? Isn't it important to set that to something other than default? Have you been running the spindle long without issues?



  7. #67
    Registered Dytoven's Avatar
    Join Date
    Apr 2015
    Posts
    17
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    I have PD011-0 as factory default and I remember that the change gave me problems, was running more than 10 minutes on the floor to test with tachometer, do not warm or making strange noises, but I have not tried still in real work. I hope it works well too.



  8. #68
    Registered
    Join Date
    Apr 2011
    Location
    USA
    Posts
    31
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by Dytoven View Post
    I have PD011-0 as factory default and I remember that the change gave me problems, was running more than 10 minutes on the floor to test with tachometer, do not warm or making strange noises, but I have not tried still in real work. I hope it works well too.
    Will you elaborate on what types of problems? Sorry for all the questions, I'm just trying to be thorough.



  9. #69
    Registered Dytoven's Avatar
    Join Date
    Apr 2015
    Posts
    17
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    I have no experience with these products and my knowledge of electricity and electronics is basic, but when you enter some incorrect parameter sure resulting in low speed, vibration or bad sound.
    I read faster than you can adjust the torque, but I have not tried. If you make it, write something here.
    Sometimes one can only rely on luck.
    Now I just see in my motor plate that says "fail". certainly they sold me something rectified.



  10. #70
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by Dytoven View Post
    I have PD011-0 as factory default and I remember that the change gave me problems, was running more than 10 minutes on the floor to test with tachometer, do not warm or making strange noises, but I have not tried still in real work. I hope it works well too.
    PD011 It will not cause you problems, you will get problems if you don't set it, this is the minimum speed that the spindle is allowed to run, it should always be set to the slowest speed to suit your spindle, for your air cooled spindles around 200 Hz, is probably the best you can hope for without over heating

    Mactec54


  11. #71
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by btsioles View Post
    Thanks for the reply. I'm confused. The spindle says 300Hz. Where do you see it's 400 Hz? I should set PD011 TO 300? Why are others using 120?
    In the second photo, I see why, that is for countries that use 50 Hz

    The others are water cooled spindles & can run slower, yours being air cooled they can not run that slow as they rely on the motor fan to keep them cool

    200 should be fine for PD011, just check the temperature if it gets hotter than what it is at 18,000 then increase to 220 & try it Etc

    Acceleration & Deceleration should be similar numbers also, Deceleration is just as important as Acceleration if it takes 15s to get up to speed then Deceleration should be similar, no less than 12s

    Mactec54


  12. #72
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by Dytoven View Post
    I have no experience with these products and my knowledge of electricity and electronics is basic, but when you enter some incorrect parameter sure resulting in low speed, vibration or bad sound.
    I read faster than you can adjust the torque, but I have not tried. If you make it, write something here.
    Sometimes one can only rely on luck.
    Now I just see in my motor plate that says "fail". certainly they sold me something rectified.
    There is no luck about it, the Parameters have to be correct, or Fail it will be

    The VFD Drive will fail in a flash, with using wrong settings, this is not something you can just set any Parameter & press the start button, ( 1 ) wrong setting can/will smoke your drive

    Mactec54


  13. #73
    Registered
    Join Date
    Apr 2011
    Location
    USA
    Posts
    31
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Great, thanks for the info mactec54. I'll try this tonight and report back.



  14. #74
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    btsioles

    I did not see in your list PD 014 & PD 015

    PD 014=12 Acceration
    PD 012=12 Deceleration

    These need to be set, you can start at 15s, you can adjust to a lower setting when you get used to how your spindle runs

    Mactec54


  15. #75
    Registered
    Join Date
    Apr 2011
    Location
    USA
    Posts
    31
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by mactec54 View Post
    btsioles

    I did not see in your list PD 014 & PD 015

    PD 014=12 Acceration
    PD 012=12 Deceleration

    These need to be set, you can start at 15s, you can adjust to a lower setting when you get used to how your spindle runs
    Great. Thanks so much for the info. I will set both PD014 and PD015 to 15. Hopefully with these changes, and PD070 to 1, I will be set. I will report back tonight.



  16. #76
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    btsioles

    If you do PD070 then set these Parameters also

    PD072=300

    PD73=200

    Mactec54


  17. #77
    Registered
    Join Date
    Apr 2011
    Location
    USA
    Posts
    31
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by mactec54 View Post
    btsioles

    If you do PD070 then set these Parameters also

    PD072=300

    PD73=200
    Okay. How about pd144? Is that max rpm 18000 / 8 amps, giving 2250? Or do I use 3000? Is PD070 = 1 the solution to my ROTT problem?



  18. #78
    Registered
    Join Date
    Apr 2011
    Location
    USA
    Posts
    31
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Okay, the suggestions seem to have worked. Here is a recap.

    3kw 300hz 18000rpm air cooled square spindle. Inverter input 240v USA.

    The following settings in this order:

    Reset to factory defaults
    Pd001=0
    005=300
    004=300
    003=300
    072=300
    073=200
    006=2.5
    008=220
    009=15
    010=8
    011=200
    014=15
    015=15
    070=1
    142=8.6 (motors amp rating)
    143=2
    144=3000

    I only ran it up to speed then stopped it. Rott showed 18000, Hz showed 300. I'll run it for an extended period this weekend to verify it's not getting too hot.

    Thanks everyone for the help!



  19. #79
    Member mactec54's Avatar
    Join Date
    Jan 2005
    Location
    USA
    Posts
    15362
    Downloads
    0
    Uploads
    0

    Default Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by btsioles View Post
    Okay. How about pd144? Is that max rpm 18000 / 8 amps, giving 2250? Or do I use 3000? Is PD070 = 1 the solution to my ROTT problem?
    Use the 3000 for the PD144

    As for the PD070, it has more than ( 1 ) use, there would be no harm in trying it at default of ( 0 ), to see if you have any change in the RPM, it is normally used for a remote analog pot/control, now that PD072/PD073 is set, all ( 3 ) Parameters are related

    Mactec54


  20. #80
    Registered
    Join Date
    Apr 2011
    Location
    USA
    Posts
    31
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by mactec54 View Post
    Use the 3000 for the PD144

    As for the PD070, it has more than ( 1 ) use, there would be no harm in trying it at default of ( 0 ), to see if you have any change in the RPM, it is normally used for a remote analog pot/control, now that PD072/PD073 is set, all ( 3 ) Parameters are related
    Thanks for the info. So I just ran spindle at 200 Hz for about 5 minutes. Then up to 250 for a few more minutes. Then 300 for a few more. In that 10 minutes or so the round black spindle body above the collet side got warmer than I expected. The square body was not as warm, but was warm to the touch. I hadn't expected it to get warm that fast. I wonder how warm it would get while cutting.

    Is this normal?



Page 4 of 41 FirstFirst 123456714 ... LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Huanyang Chinese VFD settings and manual here!

Huanyang Chinese VFD settings and manual here!