Six jaw chuck for Shopmaster

Results 1 to 5 of 5

Thread: Six jaw chuck for Shopmaster

  1. #1
    Registered Goodlett's Avatar
    Join Date
    Aug 2011
    Location
    USA
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Six jaw chuck for Shopmaster

    Seems like I am always chucking stuff by the threads so I decided to look at getting a six jaw chuck to hopefully cause less damage to threads. I ordered a cheap Chinese Sanou six jaw 6 inch chuck off Ebay. It arrived in 4 or 5 days and fit my machine without any modification to anything. The chuck was full of grinding dust and grit so I cleaned it thoroughly.

    Shockingly, the thing seems to hold a thou and a half of run out through its' range. Maybe I got lucky.

    Similar Threads:
    Attached Thumbnails Attached Thumbnails Six jaw chuck for Shopmaster-img_3309-jpg  


  2. #2
    Registered RussellCofID's Avatar
    Join Date
    May 2016
    Location
    United States
    Posts
    17
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by Goodlett View Post
    Seems like I am always chucking stuff by the threads so I decided to look at getting a six jaw chuck to hopefully cause less damage to threads. I ordered a cheap Chinese Sanou six jaw 6 inch chuck off Ebay. It arrived in 4 or 5 days and fit my machine without any modification to anything. The chuck was full of grinding dust and grit so I cleaned it thoroughly.

    Shockingly, the thing seems to hold a thou and a half of run out through its' range. Maybe I got lucky.
    Great to hear a good review, you hear so many bad ones you'd think SOMEONE would start making good ones. Keep us posted on projects and uses for the 6-jaw.

    Russell C of Idaho
    Big trains and big dreams...


  3. #3
    Registered
    Join Date
    Sep 2015
    Posts
    36
    Downloads
    0
    Uploads
    0

    Default Re: Six jaw chuck for Shopmaster

    I bought an American Made Kalamazoo Chuck Six jaw chuck for Shopmaster-20161129_182218_resized-jpg
    It has microset capability to true it in. They also made an adapter to the 2015 Millturn head stock.
    The final runout was too small to measure less than 0.002 mm

    Attached Thumbnails Attached Thumbnails Six jaw chuck for Shopmaster-20161129_182218_resized-jpg  


  4. #4
    Registered Goodlett's Avatar
    Join Date
    Aug 2011
    Location
    USA
    Posts
    13
    Downloads
    0
    Uploads
    0

    Default Re: Six jaw chuck for Shopmaster

    I didn't know a set-through type chuck was even an option for this machine.



  5. #5
    Registered
    Join Date
    Sep 2015
    Posts
    36
    Downloads
    0
    Uploads
    0

    Default Re: Six jaw chuck for Shopmaster

    When I was setting up my machine in the fall of 2015, I had a number of challenges, I eventually checked all the tolerances of the machine against the guaranteed accuracy that was listed on the shopmaster website at the time shee.jpg attached below.

    Besides the problems with the Tail-stock and the main carriage, i noted that the headstock was outside specs.
    a. Using the longitudinal carriage after removing the mill table I was able to confirm that some of the critical measurements were over double the factory manufacturing tolerances.
    i. G2.a Spindle float was less than 0.00005”
    ii. G2.b radial centering was 0.00165"
    iii. G4.a was 0.0022" at the spindle end
    iv. G4.b was 0.0036" 6” from the spindle end

    Note that in separate specs it quoited SPINDLE ACCURACY T.I.R. 0.00076?

    I traced part of the problem to the actual chuck and the spindle. I looked at Bison, Buck and Kalamazoo chucks and settled on the Kalamazoo 6 jaw. model 3665 with guaranteed TIR of 0.0005" again because i wanted to minimize damage to threaded ends.

    Micro Set Manual Chucks - Solid Jaws from Kalamazoo Chuck Manufacturing 1-888-727-4703

    I sent Kalamazoo my spindle and they machined an adapter to fit their 6 jaw chuck.

    I trued up the spindle and bolted on the new chuck and tested and the TIR was less than 0.002mm or 0.0000787".


    Six jaw chuck for Shopmaster-shee-jpg

    Attached Thumbnails Attached Thumbnails Six jaw chuck for Shopmaster-shee-jpg  


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Six jaw chuck for Shopmaster

Six jaw chuck for Shopmaster