Servo Motors / Drives


Page 1 of 154 12341151101 ... LastLast
Threads 1 to 20 of 3070

Forum: Servo Motors / Drives

Discuss servo motors, drivers and other related topics here.

  1. AC Servo motors, are they all three phase?

    Started by csreades‎, Yesterday 01:26 PM
    drive, phase, power, required, servo
    • Replies: 5
    • Views: 133
    Yesterday, 10:52 PM Go to last post
  2. Motors for small production machine.

    Started by strantor‎, 01-11-2021 04:53 PM
    5 Pages
    1 2 3 4 5
    • Replies: 80
    • Views: 1,918
    01-24-2021, 11:43 AM Go to last post
  3. CNCdrive DG4S-08020 reset question

    Started by bhdavis1cnc‎, 01-22-2021 01:01 PM
    back, movement, reset, software, tuning
    • Replies: 0
    • Views: 76
    01-22-2021, 01:01 PM Go to last post
    • Replies: 1
    • Views: 138
    01-21-2021, 01:18 AM Go to last post
  4. New Machine Build- CNC Router Build Using Servo Motors

    Started by St_Maurice‎, 11-13-2020 03:31 PM
    • Replies: 8
    • Views: 699
    01-09-2021, 11:59 AM Go to last post
  5. simodrive 611, 6SN1123-1AB00-0EA0

    Started by Alfredok66‎, 01-05-2021 07:23 AM
    change, display, motor, run, simodrive
    • Replies: 0
    • Views: 193
    01-05-2021, 07:23 AM Go to last post
    • Replies: 2
    • Views: 638
    01-02-2021, 11:24 AM Go to last post
  6. Need Help!- Looking for Logosol - FlashCut Servo Drive

    Started by ponthieux‎, 08-20-2008 10:33 AM
    • Replies: 1
    • Views: 1,500
    01-01-2021, 12:04 AM Go to last post
    • Replies: 0
    • Views: 389
    12-15-2020, 03:24 AM Go to last post
  7. ClearPath Servos - Do they lock like a stepper

    Started by bobmagnuson‎, 09-29-2018 06:18 PM
    effort, gantry, place, servos, steppers
    • Replies: 19
    • Views: 3,462
    12-08-2020, 08:58 PM Go to last post
  8. Mitsubishi MR-J2s-A Help needed - alarm prob

    Started by kudos‎, 04-22-2011 02:31 PM
    mr-j2s-a, then
    • Replies: 16
    • Views: 34,962
    12-08-2020, 07:01 AM Go to last post
  9. Step/dir Servo Drive selection

    Started by WesM‎, 12-02-2020 12:54 AM
    cnc, drives, recommend, servo, servos
    • Replies: 4
    • Views: 389
    12-02-2020, 03:50 AM Go to last post
  10. Need Help!- Yaskawa DR2 servopack made with RS422/485 interface

    Started by Grubma‎, 01-24-2009 08:52 AM
    2 Pages
    1 2
    • Replies: 38
    • Views: 12,134
    11-30-2020, 11:31 AM Go to last post
  11. Yaskawa Varispeed 626VM3 Help

    Started by Derwood1723‎, 06-18-2012 10:08 PM
    2 Pages
    1 2
    • Replies: 33
    • Views: 16,412
    11-30-2020, 04:02 AM Go to last post
  12. Newbie- Baruffaldi DMS 07

    Started by rackrall‎, 11-22-2020 07:46 AM
    • Replies: 1
    • Views: 498
    11-22-2020, 07:57 PM Go to last post
  13. 6 wire ac servo motors

    Started by APPLEJACK‎, 11-20-2020 02:49 PM
    advantages, arrangement, connect, servo, windings
    • Replies: 0
    • Views: 200
    11-20-2020, 02:49 PM Go to last post
  14. Alternative to Mitchell Electronics TI-5000

    Started by learning_elec‎, 12-11-2019 12:22 AM
    alternative, mitchell, run, subscription, system
    • Replies: 2
    • Views: 858
    11-17-2020, 03:48 PM Go to last post
  15. Need Help!- Toshiba RAD10-006 Datasheet

    Started by ArosabayCNC‎, 11-16-2020 04:25 PM
    datasheet, pinout, require, reuse, success
    • Replies: 0
    • Views: 126
    11-16-2020, 04:25 PM Go to last post
  16. What is - Torque Mode? Position Mode? Speed/Velocity Mode?

    Started by sunmix‎, 10-25-2008 01:32 PM
    3 Pages
    1 2 3
    • Replies: 47
    • Views: 28,841
    11-13-2020, 11:35 AM Go to last post
  17. Electrocraft BRU-200 Drive questions

    Started by Verboten‎, 01-29-2004 02:48 PM
    3 Pages
    1 2 3
    brushless, buy, cheap, craft, direction, drive, electro, electrocraft, formation, home, http:, ice, information, motion, motor, nice, not, pdf, pin, ques, question, questions, running, servo, servo drive, step, step and direction, working
    • Replies: 50
    • Views: 23,210
    11-13-2020, 08:53 AM Go to last post

Page 1 of 154 12341151101 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 31 users browsing this forum. (1 members & 30 guests)

  1. Al_The_Man

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands