Allen Bradley Ultra3000 and MPL servo


Results 1 to 5 of 5

Thread: Allen Bradley Ultra3000 and MPL servo

  1. #1
    Member jcsb's Avatar
    Join Date
    Sep 2011
    Location
    United States
    Posts
    42
    Downloads
    3
    Uploads
    0

    Default Allen Bradley Ultra3000 and MPL servo

    I am stuck on trying to find out what is going on with this combo. I'm hooking up the servo drive and communications cable and getting a E11 error, which is "phasing not correct". This has happened on two separate motors and drives. I've checked the wiring many times. I've tried changing the orientation of UVW to see if I can get anything else. Nothing is getting me there. I should note that I'm a retired mechanical engineer so while familiar with servo drives I'm certainly no expert. Both drives and and servo's were purchased used but have checked out for shorts, continuity, and such. Does this setup require me utilize a program to set up the servo to remove the E11 error? Any help would be greatly appreciated.
    Thanks,
    John

    Similar Threads:


  2. #2
    Member machinehop5's Avatar
    Join Date
    Aug 2009
    Location
    United States
    Posts
    715
    Downloads
    2
    Uploads
    0

    Default Re: Allen Bradley Ultra3000 and MPL servo

    ...the encoder and feedback phase makes a difference too. right?



  3. #3
    Member jcsb's Avatar
    Join Date
    Sep 2011
    Location
    United States
    Posts
    42
    Downloads
    3
    Uploads
    0

    Default Re: Allen Bradley Ultra3000 and MPL servo

    Yes it does. I've checked the voltage to the encoder and it's correct. I need to get my scope out and check the output next.
    John



  4. #4
    Member Iron-Man's Avatar
    Join Date
    Jan 2009
    Location
    United States
    Posts
    327
    Downloads
    0
    Uploads
    0

    Default Re: Allen Bradley Ultra3000 and MPL servo

    Quote Originally Posted by jcsb View Post
    I am stuck on trying to find out what is going on with this combo. I'm hooking up the servo drive and communications cable and getting a E11 error, which is "phasing not correct". This has happened on two separate motors and drives. I've checked the wiring many times. I've tried changing the orientation of UVW to see if I can get anything else. Nothing is getting me there. I should note that I'm a retired mechanical engineer so while familiar with servo drives I'm certainly no expert. Both drives and and servo's were purchased used but have checked out for shorts, continuity, and such. Does this setup require me utilize a program to set up the servo to remove the E11 error? Any help would be greatly appreciated.
    Thanks,
    John

    Hello JCSB

    These are not connect and run systems, they must be set and configured for the connected motor type.

    The manual: https://literature.rockwellautomatio...n005_-en-p.pdf


    You need the UltraWARE software at: https://compatibility.rockwellautoma...aspx?crumb=112


    See page 100 for: E11 Illegal Hall State.

    Verify the correct wiring of the hall phases for commutation and select the proper motor, see PAGE 21, this should correct the problem. Remember you have (UVW power stage) and (Hall sensor states for commutation).

    Hope this helps,

    Iron-Man

    Last edited by Iron-Man; 09-08-2020 at 08:09 PM. Reason: Motor Type must be set.


  5. #5
    Member jcsb's Avatar
    Join Date
    Sep 2011
    Location
    United States
    Posts
    42
    Downloads
    3
    Uploads
    0

    Default Re: Allen Bradley Ultra3000 and MPL servo

    Thanks. I will try to resolve this tomorrow.
    John



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Allen Bradley Ultra3000 and MPL servo

Allen Bradley Ultra3000 and MPL servo

Allen Bradley Ultra3000 and MPL servo