Electrocraft BRU-200 Drive questions

[bsb]

we have a electro-craft bru-200 dm30 and it stopped working and it comes up with a watchdog time out error, has anyone seen this error and is there anything I can do without sending it to a repair shop thanks

[Jan-Willem]

we have a electro-craft bru-200 dm30 and it stopped working and it comes up with a watchdog time out error, has anyone seen this error and is there anything I can do without sending it to a repair shop thanks

We've got the same problem here. Anyone know what's the problem ? Is the timekeeper ram the problem ?

[cstidham]

Did you ever get this problem resolved with your DM-30? I'm currently chasing the same issue.

[Jan-Willem]

Did you ever get this problem resolved with your DM-30? I'm currently chasing the same issue.

I've solved the problem. I've found the manual.
If led 2 and 4 are on this means that the timekeeper is defect.
I've programmed a new timekeeper and it's working again.

I didn't try to make connection to the drive with a communication cable and software because the machine had to much work. However it should be possible.

[cstidham]

How did you make a new time keeper? Can you send me a copy of your manual? I haven't been able to find it to d/l. I have another identical unit this is functional on another machine, I would like to be able to grab that configuration and upload to a new(er) drive that I have. The lights that I have on are: 1-green, 3&4 are red.

[cstidham]

your account is not set up to receive a private message but

my email address is chuckstidham@yahoo.com

[Jan-Willem]

e-mail has been sent.

[MojsterMiha]

Anyone have manual for electro craft bru 200?
I would need it urgently.
Have also s/w for programming?

If you could help me... I will be very grateful.

andrej.zima1970@gmail.com


Thank you!

Andrej

[Al_The_Man]

email sent.
Al.

[xjdubber]

I have set up comms with these drives before, there is terminal that was used to communicate with these drives and there is emulators online somewhere that will work, the comms are rs232 i have a schematic for the cable and the software at work. If anyone is interested ill post up the info next week sometime.

[Jan-Willem]

I have set up comms with these drives before, there is terminal that was used to communicate with these drives and there is emulators online somewhere that will work, the comms are rs232 i have a schematic for the cable and the software at work. If anyone is interested ill post up the info next week sometime.

I'm interested.

[MojsterMiha]

Me too...

[rjevcic]

Hello,

I need manual for BRU-200, too. I will be very glad if anybody have this document and could send it to robert.jevcic@gmail.com.
Thank You very much...

[ciekawy1291]

hello,
i have a problem with my bender. its a old herber with two servo drive electro craft bru 200. my problem concerns one of them. on servo lights one green led and three reds. bender works 30 min and the fault is on the servo drive. please help.

[davor_sa]

I'm interested.
Thanks in advance!

[davor_sa]

I have also to repair machine old Herber 76 cnc with two servo drive electro craft bru 200.I would like to exchange expirence with you about repair.Already repair power supply and PLC but I can not start axis motors.some problems with bru-200 dm30 modul!

[davor_sa]

Can you send me some advice how to connect.Thanks in advance!
kukurikuus@gmail.com

[xjdubber]

Ok the manual has finally made it from the machine back to my desk, unfortuneately the last 6 months have been the bussiest of my life once i get time i will scan it and post it up

[mike_Kilroy]

Search this forum: I have posted link to my online cc of manual more than once....

[mike_Kilroy]

Search this forum: I have posted link to my online cc of manual more than once....

here is link yet again:

https://app.box.com/s/t84rxtbkz82vtlhmv4xk

147 pages. enjoy.