Mach3 2010 Screen set - Page 121


Page 121 of 121 FirstFirst ... 2171111118119120121
Results 1,441 to 1,449 of 1449

Thread: Mach3 2010 Screen set

  1. #1441
    Member
    Join Date
    Apr 2008
    Location
    Slovenia
    Posts
    27
    Downloads
    0
    Uploads
    0

    Default Re: Mach3 2010 Screen set

    Yes i have tried rebooting PC and restart mach 3. My Mach Version is R.3.043.062
    It must be something that i have missed. it is repeatable and it happens always when machine gets over 900mm in Y axis. Same happens if i move parking position to lets say 910mm.
    I think it is Softlimit.
    If i disable soft limit checkbox this dosent happen.
    My softlimit is set to 950mm in settings of mach 3 so I dont know why it is triggered at 900.
    Take a look at my settings is something missing.

    Mach3 2010 Screen set-img_4524-jpgMach3 2010 Screen set-img_4525-jpg

    Attached Thumbnails Attached Thumbnails Mach3 2010 Screen set-img_4524-jpg   Mach3 2010 Screen set-img_4525-jpg  


  2. #1442
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    34534
    Downloads
    0
    Uploads
    0

    Default Re: Mach3 2010 Screen set

    It might be something to do with the ESS plugin and how it handles softlimits.

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  3. #1443
    Member
    Join Date
    Apr 2008
    Location
    Slovenia
    Posts
    27
    Downloads
    0
    Uploads
    0

    Default Re: Mach3 2010 Screen set

    But this only happens when running macro, if i jog machine i can jog it to 950mm like it should be.
    And if i jog it it has slow zone before reaches 950mm in macro it is sudden stop at 900mm.
    If you look picture in my previous post in 2010 screenset under tab limits section program limits, should i input some values there ?



  4. #1444
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    34534
    Downloads
    0
    Uploads
    0

    Default Re: Mach3 2010 Screen set

    The macros (and screenset) have nothing to do with softlimits. I'm guessing that it's the way the ESS deals with macros and softlimits, and is probably a bug in their plugins.

    I'd contact Warp9 and see what they have to say. I don't recall ever hearing about this issue in 9+ years, and thousands of users.

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  5. #1445
    Member
    Join Date
    Apr 2008
    Location
    Slovenia
    Posts
    27
    Downloads
    0
    Uploads
    0

    Default Re: Mach3 2010 Screen set

    I figured it out, it was my slave axis.
    It looks like that when running macro it checks also slave axis soft limits but when joging it is ok.
    My slave axis was set to 900 so machine always stopped if i moved touch plate out of range.



  6. #1446
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    34534
    Downloads
    0
    Uploads
    0

    Default Re: Mach3 2010 Screen set

    Could be because the macro is sending g-code commands. The ESS must ignore the slave softlimit setting when jogging, but not when running g-code??

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  7. #1447
    Member
    Join Date
    Apr 2008
    Location
    Slovenia
    Posts
    27
    Downloads
    0
    Uploads
    0

    Default Re: Mach3 2010 Screen set

    Now i'm using screen set without problems with movable touch plate for z and fixed touch plate for reference. Both are hard without movable parts.

    But now i'm thinking to get a 3d touch probe for XYZ and new fixed touch plate for table with movable surface. Like on photos below.
    Mach3 2010 Screen set-3d-touch-probe-pngMach3 2010 Screen set-tools-lenght-sensor-png

    Is there a way to use macro with this kind of acessories.
    Ok for 3d touch probe i would use wizard for Y and X.
    But i see problem for z axis.
    If i run initial Z zero routine probe will touch off part and then go to fixed touch plate witch is also movable in z direction so reading probably wont be accurate as i dont know what will move first 3d probe or touch sensor. Both has cca same 2N touch force.

    Any idea how to implement 3d touch probe in that combination .
    Solution would be to use fixed plate without movable parts as that would be true reference, but for safety i would rather use movable tool sensor.



  8. #1448
    Community Moderator ger21's Avatar
    Join Date
    Mar 2003
    Location
    Shelby Township
    Posts
    34534
    Downloads
    0
    Uploads
    0

    Default Re: Mach3 2010 Screen set

    I can't think if any way to use both for the initial Z zero.

    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)


  9. #1449
    Member
    Join Date
    Jan 2018
    Location
    United Kingdom
    Posts
    30
    Downloads
    0
    Uploads
    0

    Default Re: Mach3 2010 Screen set

    Quote Originally Posted by lukahr View Post
    Any idea how to implement 3d touch probe in that combination .
    Solution would be to use fixed plate without movable parts as that would be true reference, but for safety i would rather use movable tool sensor.
    I use that combination of tool setter and probe all the time. You can see how I measure and correct for the error in this video https://youtu.be/LTtalZjEj4c



Page 121 of 121 FirstFirst ... 2171111118119120121

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Mach3 2010 Screen set

Mach3 2010 Screen set

Mach3 2010 Screen set