Rutex Products

Page 1 of 2 12 LastLast
Threads 1 to 20 of 27

Forum: Rutex Products

Discuss Rutex here.

Sub-Forums Threads / Posts  Last Post

  1. Servo Drives

    (1 Viewing)

    Discuss all Rutex servo drives and get direct support!

    Forum Actions:

    Forum Statistics:

    • Threads: 168
    • Posts: 1,346
  1. Question time to deliver rutex product?

    Started by grebator‎, 06-27-2007 07:33 AM
    not
    • Replies: 16
    • Views: 14,004
    12-29-2007, 09:21 AM Go to last post
  2. What dc voltage to use on rutex R90H drive

    Started by BOB F‎, 02-27-2005 10:08 AM
    980, cnc, drive, servo, volt, voltage
    • Replies: 17
    • Views: 13,027
    11-28-2005, 11:22 AM Go to last post
  3. Rutex THC product availability

    Started by rutexus‎, 11-28-2007 10:10 AM
    indicate, its, not, say
    • Replies: 0
    • Views: 12,108
    11-28-2007, 10:10 AM Go to last post
  4. Rutex R510 A/B Plasma Controller

    Started by kanankeban‎, 11-06-2004 05:22 PM
    • Replies: 12
    • Views: 11,944
    01-14-2005, 10:27 AM Go to last post
  5. R990h

    Started by dpaulson‎, 02-21-2005 03:10 PM
    board, encoder, indicate, maybe, not, onto, plasma., r90h, r990h, takes
    • Replies: 2
    • Views: 10,454
    02-22-2005, 10:35 AM Go to last post
  6. Rutex system uncontrollable after computer replacement.

    Started by Splint‎, 11-13-2019 11:36 PM
    computer, drive, drives, motherboard, software
    • Replies: 2
    • Views: 10,093
    11-16-2019, 06:41 AM Go to last post
  7. What to buy from rutex to get going........

    Started by Apples‎, 05-13-2005 12:41 AM
    buy, cor, list, not, oxy, plasma, table, then
    • Replies: 11
    • Views: 9,565
    03-01-2006, 11:05 AM Go to last post
  8. Terco 45(00)

    Started by amo‎, 12-07-2007 01:34 PM
    • Replies: 1
    • Views: 9,465
    09-03-2009, 04:29 AM Go to last post
  9. Talking Rutex 510A

    Started by ty1295‎, 05-13-2004 02:16 PM
    • Replies: 9
    • Views: 9,285
    09-29-2005, 08:13 PM Go to last post
  10. rutex and mach3

    Started by dgalaxy‎, 12-11-2006 10:57 AM
    • Replies: 10
    • Views: 9,248
    12-16-2006, 09:19 PM Go to last post
  11. R990H

    Started by Rickylee53‎, 03-14-2013 03:17 PM
    • Replies: 1
    • Views: 8,166
    03-16-2013, 12:28 PM Go to last post
  12. programming software

    Started by greggwhatley‎, 11-26-2012 08:01 AM
    • Replies: 0
    • Views: 8,055
    11-26-2012, 08:01 AM Go to last post
  13. Trouble contacting Rutex

    Started by Hasher‎, 07-26-2006 11:10 PM
    contacting, drow, landline, replys, ringing, rutex, trouble
    • Replies: 8
    • Views: 7,769
    02-28-2007, 08:34 AM Go to last post
  14. Need Help!- What Voltage are my Servo's?

    Started by austin.mn‎, 08-21-2009 05:53 PM
    away, dc servos, dls, onto, then, went
    • Replies: 4
    • Views: 7,651
    09-19-2009, 06:21 PM Go to last post
  15. Using 3 phase with the Motherboard?

    Started by svenakela‎, 04-15-2009 07:19 AM
    cause, not
    • Replies: 0
    • Views: 7,597
    04-15-2009, 07:19 AM Go to last post
  16. Unhappy R90h not detected

    Started by jeff8451‎, 12-21-2009 10:48 PM
    its, not, saw
    • Replies: 0
    • Views: 7,388
    12-21-2009, 10:48 PM Go to last post
  17. need help hooking up encoder

    Started by CNC Darren‎, 02-26-2007 05:45 PM
    r2210, wan
    • Replies: 3
    • Views: 7,140
    03-02-2007, 12:37 AM Go to last post
  18. Unhappy trouble with configure and testing R990H servo drive

    Started by visky‎, 10-30-2007 07:02 AM
    • Replies: 1
    • Views: 6,891
    11-01-2007, 08:40 PM Go to last post
  19. Troubles finding the right motor for the drive

    Started by Progger‎, 04-18-2007 09:47 AM
    • Replies: 2
    • Views: 6,761
    07-16-2007, 09:28 AM Go to last post
  20. Problem- rutex capacitor

    Started by HCE‎, 11-08-2022 01:28 PM
    • Replies: 0
    • Views: 6,444
    11-08-2022, 01:28 PM Go to last post

Page 1 of 2 12 LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 2 users browsing this forum. (0 members & 2 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands