Planet CNC THC. - Page 2

Page 2 of 2 FirstFirst 12
Results 21 to 29 of 29

Thread: Planet CNC THC.

  1. #21
    Member
    Join Date
    Jun 2017
    Location
    Norway
    Posts
    119
    Downloads
    0
    Uploads
    0

    Default Re: Planet CNC THC.

    Quote Originally Posted by PlanetCNC View Post
    Sdt - Set delay time from 0.1 to 9.9 sec. Time between Arc OK signal appears and generation of signals up and down is enabled. Factory setting 0.5 s.


    HYS - Hysteresis from 2V to 32V (2 V step). Voltage frame around reference. If arc voltage is higher than Ref + HYS/2 then down signal is generated. If voltage is lower than Ref - HYS/2, up signal is generated. Factory setting 6 V.


    AdL - Ant-dive limit from 50V to 300V. Arc voltage that disables THC. If voltage goes higher than Anti-dive limit all output signals go low. The parameter’s value must be set higher than reference voltage. Factory setting 220V.


    tSt - Test mode. Only available when no arc voltage present! Pressing V or ? button generate output signals. The display indicates direction.
    tSt - Test mode. Only available when no arc voltage present! Pressing V or ? buttongenerate output signals. The display indicates direction.


    So when you use this Test Mode. Should you get a input signal on TNG Up/down input to where you connected your wires?



  2. #22
    Member
    Join Date
    Jun 2017
    Location
    Norway
    Posts
    119
    Downloads
    0
    Uploads
    0

    Default Re: Planet CNC THC.

    Quote Originally Posted by MrEmo View Post
    tSt - Test mode. Only available when no arc voltage present! Pressing V or ? buttongenerate output signals. The display indicates direction.


    So when you use this Test Mode. Should you get a input signal on TNG Up/down input to where you connected your wires?
    Yes/No?

    The reason I am asking is that I am not getting these signals when I run this mode and push up and down.



  3. #23
    Member
    Join Date
    Jun 2017
    Location
    Norway
    Posts
    119
    Downloads
    0
    Uploads
    0

    Default Re: Planet CNC THC.

    Quote Originally Posted by MrEmo View Post
    Yes/No?

    The reason I am asking is that I am not getting these signals when I run this mode and push up and down.
    Hello?

    I am trying to tell you that your THC is not working as it should. It is not sending up or down signal in test mode and I am not receiving signals in the software...



  4. #24
    Member PlanetCNC's Avatar
    Join Date
    Mar 2017
    Location
    Slovenia
    Posts
    1295
    Downloads
    0
    Uploads
    0

    Default Re: Planet CNC THC.

    In test mode, when you press button, what does THC display show?



  5. #25
    Member
    Join Date
    Jun 2017
    Location
    Norway
    Posts
    119
    Downloads
    0
    Uploads
    0

    Default Re: Planet CNC THC.

    Quote Originally Posted by PlanetCNC View Post
    In test mode, when you press button, what does THC display show?
    See attached photos.

    Attached Thumbnails Attached Thumbnails Planet CNC THC.-190725856_587623092209159_8035172001125385895_n-jpg   Planet CNC THC.-190705152_398618171265498_8527590576125251711_n-jpg  


  6. #26
    Member PlanetCNC's Avatar
    Join Date
    Mar 2017
    Location
    Slovenia
    Posts
    1295
    Downloads
    0
    Uploads
    0

    Default Re: Planet CNC THC.

    This is ok. How is controller connected to thc?



  7. #27
    Member
    Join Date
    Jun 2017
    Location
    Norway
    Posts
    119
    Downloads
    0
    Uploads
    0

    Default Re: Planet CNC THC.

    Quote Originally Posted by PlanetCNC View Post
    This is ok. How is controller connected to thc?
    50:1.

    I get voltage on the thc when machine running.

    But I am not getting signals on software on the inputs that are designated. Nothing is showing up on I/O thingy.



  8. #28
    Member PlanetCNC's Avatar
    Join Date
    Mar 2017
    Location
    Slovenia
    Posts
    1295
    Downloads
    0
    Uploads
    0

    Default Re: Planet CNC THC.

    On your photos all wires are black. I want to know how THC is connected to controller.



  9. #29
    Member
    Join Date
    Jun 2017
    Location
    Norway
    Posts
    119
    Downloads
    0
    Uploads
    0

    Default Re: Planet CNC THC.

    Quote Originally Posted by PlanetCNC View Post
    On your photos all wires are black. I want to know how THC is connected to controller.
    I swapped some wires around. I have tried several ways to connect the Common wire and I went back to one of the first ways I connected it and now it decided to work.

    But fear not, I am not done yet.

    I have a new problem.

    I am now back to having ARC OK signal on input 7. The machine starts cutting but then it suddenly stops. I am unable to restart the machine within the software. Nothing is working, start, stop, pause, emergency stop does nothing.

    Try to reboot software still not able to start machine.

    If I remove ARC OK from settings I am able to proceed or I have to reboot hardware.

    So this has something to do with ARC OK must be something in the software?

    Last edited by MrEmo; 05-28-2021 at 03:58 AM.


Page 2 of 2 FirstFirst 12

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Planet CNC THC.

Planet CNC THC.