Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software

Results 1 to 8 of 8

Thread: Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software

  1. #1
    Registered
    Join Date
    Jan 2018
    Location
    United States
    Posts
    4
    Downloads
    0
    Uploads
    0

    Angry Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software

    I downloaded the TNG software and followed the instructions to install. After I upgraded the controller firmware and drivers, I cannot use the old software. I do not have my license key yet (hopefully in tomorrow’s email) so I tried to do some work with the old software. Now nothing is working. ;-(

    Is the new firmware backwards compatible with the old software?

    Similar Threads:


  2. #2
    Moderator PlanetCNC's Avatar
    Join Date
    Mar 2017
    Location
    Slovenia
    Posts
    248
    Downloads
    0
    Uploads
    0

    Default Re: Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software

    If you want to use CNC USB controller software once your controller is updated with PlanetCNC TNG software:
    -In PlanetCNC TNG click: Machine/Controller/Advanced/Revert to V1
    -Close TNG
    -Open CNC USB controller software and update firmware: Machine/Update Firmware



  3. #3
    Member
    Join Date
    Oct 2017
    Posts
    20
    Downloads
    0
    Uploads
    0

    Default Re: Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software

    Hi
    As I was advised to use for threading TNG
    I installed it, updated the firmware of my card.
    Now CNC USB Controller does not work (In PlanetCNC TNG click: Machine/Controller/Advanced/Revert to V1 - inactive)
    In PlanetCNC TNG : connecting i see my board but I can’t go to her simulation remains selected.
    Motors no longer spin.



  4. #4
    Member
    Join Date
    Oct 2017
    Posts
    20
    Downloads
    0
    Uploads
    0

    Default Re: Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software

    I also noticed that activation code "LUxx-xxxx-xxxx-ALER" changed to CU5xx-xxxxx--xxxxx--xxxxx--xxxxx-XV5J
    I can’t activate my license.
    I looked at the post about license problems and installed the files (the dialog was different but I had messages about the successful installation) https://planet-cnc.com/certificate-import/



  5. #5
    Moderator PlanetCNC's Avatar
    Join Date
    Mar 2017
    Location
    Slovenia
    Posts
    248
    Downloads
    0
    Uploads
    0

    Default Re: Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software

    LUxx code is for CNC USB software. TNG uses different CUxx codes.
    If you have valid LUxx license then you can get free CUxx license. Contact our support.



  6. #6
    Member
    Join Date
    Oct 2017
    Posts
    20
    Downloads
    0
    Uploads
    0

    Default Re: Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software

    did the engines stop working due to the simulation mode?



  7. #7
    Member
    Join Date
    Oct 2017
    Posts
    20
    Downloads
    0
    Uploads
    0

    Default Re: Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software

    I understood why the engines do not work.
    I will write it for beginners like me.
    In the Connection menu, you need to select the device, double-click the device to change the value in Primary Controller, then click OK.
    I just selected the device and clicked OK, this method does not work, so my engines did not spin.

    But now everything works.



  8. #8
    Moderator PlanetCNC's Avatar
    Join Date
    Mar 2017
    Location
    Slovenia
    Posts
    248
    Downloads
    0
    Uploads
    0

    Default Re: Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software

    Here is described all the info needed for quick migration to PlanetCNC TNG sw:
    https://planet-cnc.com/list-essentia...tng-tutorials/



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software

Upgraded USBContoller Mk3/4 firmware via TNG now cannot use old software