PIC Programing / Design - Page 4

Page 4 of 9 FirstFirst 1234567 ... LastLast
Threads 61 to 80 of 163

Forum: PIC Programing / Design

Discuss programing of PIC chips here and design of electronics using PIC chips.

  1. Need Help!- PIC Variable frequency drive

    Started by xlukkajr‎, 01-05-2010 02:23 AM
    saw
    • Replies: 5
    • Views: 4,100
    01-19-2010, 12:27 PM Go to last post
  2. Need Help!- slow-spinning driver firmware

    Started by mossy173‎, 12-12-2009 08:53 PM
    equally, next, not
    • Replies: 5
    • Views: 2,264
    12-13-2009, 06:20 PM Go to last post
    • Replies: 2
    • Views: 2,164
    11-27-2009, 10:32 AM Go to last post
  3. what to do with unused pins on 16f84??

    Started by patriciooholegu‎, 11-06-2009 11:28 AM
    #18, almost, down
    • Replies: 12
    • Views: 5,807
    11-25-2009, 08:17 AM Go to last post
  4. newb needs advice on pic project

    Started by anilam‎, 11-09-2009 08:12 AM
    • Replies: 2
    • Views: 2,227
    11-10-2009, 02:39 AM Go to last post
  5. Lini-Stepper Revisited ( Hacked )

    Started by kowell‎, 06-29-2007 07:42 AM
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 103
    • Views: 45,006
    10-21-2009, 12:34 AM Go to last post
  6. Need Help!- Which mcu's or Stepper IC ????

    Started by jpmegadeth‎, 09-22-2009 09:03 PM
    mos
    • Replies: 1
    • Views: 2,198
    10-03-2009, 12:38 PM Go to last post
  7. PIC18F bank access

    Started by The Blight‎, 09-22-2009 06:51 AM
    keep, not, placed
    • Replies: 1
    • Views: 3,375
    09-22-2009, 02:55 PM Go to last post
  8. Newbie- Almost total ignorance

    Started by DALEK‎, 07-27-2009 06:43 AM
    almost, not, took
    • Replies: 14
    • Views: 3,587
    08-07-2009, 08:19 PM Go to last post
  9. Newbie- Pic16f628a code

    Started by Nick‎, 07-01-2009 07:33 PM
    0x1, 213, down, next, not, sub
    • Replies: 1
    • Views: 2,866
    07-02-2009, 09:31 AM Go to last post
  10. Microchip vs Atmel

    Started by Konstantin‎, 02-23-2007 01:45 AM
    3 Pages
    1 2 3
    another, available, its, mpasm, opera
    • Replies: 51
    • Views: 24,347
    06-28-2009, 12:34 AM Go to last post
  11. Need Help!- 16F84 7 segment display

    Started by Razer‎, 05-27-2009 08:47 AM
    • Replies: 8
    • Views: 3,909
    06-10-2009, 12:27 PM Go to last post
  12. Angry this thing is kicking my tail!

    Started by llilrex‎, 01-05-2008 07:41 PM
    down, isnt
    • Replies: 4
    • Views: 2,902
    06-07-2009, 08:50 AM Go to last post
  13. cnc controlled by a basic stamp.

    Started by tripolitis‎, 01-30-2008 04:52 PM
    • Replies: 6
    • Views: 5,844
    06-02-2009, 06:03 PM Go to last post
  14. MultiPic programmer for DIY'ers

    Started by slp_prlzys‎, 09-10-2005 09:32 PM
    2 Pages
    1 2
    • Replies: 21
    • Views: 12,574
    05-14-2009, 08:42 PM Go to last post
  15. Anybody build a pendant/control panel with a PIC ?

    Started by per.e‎, 07-25-2007 08:01 AM
    • Replies: 1
    • Views: 2,900
    05-10-2009, 10:27 PM Go to last post
  16. Pic programming? velleman k8048

    Started by j m‎, 07-08-2005 07:43 AM
    4 Pages
    1 2 3 4
    • Replies: 62
    • Views: 42,331
    04-12-2009, 02:56 AM Go to last post
  17. New to microcontroller

    Started by rainman‎, 03-19-2009 05:11 AM
    • Replies: 1
    • Views: 1,915
    03-19-2009, 11:08 AM Go to last post
  18. I think i am going the Linistepper route

    Started by phantomcow2‎, 11-19-2005 08:07 PM
    accept, linisteppers, lot, motors, spare
    • Replies: 1
    • Views: 3,085
    03-14-2009, 01:19 PM Go to last post
  19. Newbie- PIC 16F877A and Usart

    Started by Aster‎, 01-17-2009 02:48 AM
    isnt
    • Replies: 3
    • Views: 4,092
    03-04-2009, 08:37 AM Go to last post

Page 4 of 9 FirstFirst 1234567 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands