Phase Converters

Page 1 of 33 123411 ... LastLast
Threads 1 to 20 of 658

Forum: Phase Converters

Running 3 phase machines on single phase power discussion

  1. Need Help!- powtran i9000 settings to control 3 phase motor speed

    Started by bluebumper‎, 04-14-2018 02:37 AM
    board, ess, input, speed, vfd
    • Replies: 10
    • Views: 241
    Yesterday, 09:50 AM Go to last post
  2. Unhappy LCD panel does'nt display

    Started by bivegele‎, Yesterday 04:50 AM
    cnc, display, inverter, rpm, work
    • Replies: 0
    • Views: 77
    Yesterday, 04:50 AM Go to last post
  3. Need help! Balance voltage rotary converter motor 7.5 hp

    Started by jfroux_1‎, 04-01-2018 03:09 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 499
    04-12-2018, 08:39 AM Go to last post
  4. Need Help!- New VFD and spindle motor, RPM too low

    Started by phootsman‎, 04-04-2018 06:47 PM
    • Replies: 9
    • Views: 210
    04-07-2018, 07:52 PM Go to last post
  5. 1 phase 230v to VFD 3 phase 230V?

    Started by dukei‎, 03-26-2018 01:54 PM
    • Replies: 7
    • Views: 273
    04-04-2018, 04:21 PM Go to last post
  6. Isacon Power Control Tech Co. -HY VFD (HY01D523B)

    Started by BigWilbur‎, 03-27-2018 12:08 PM
    • Replies: 2
    • Views: 100
    03-29-2018, 10:26 AM Go to last post
    • Replies: 10
    • Views: 4,977
    03-13-2018, 02:03 PM Go to last post
  7. Rotary 3-phase converter

    Started by chuck767‎, 02-28-2018 08:44 PM
    converter, motor, phase, rotary, start
    • Replies: 2
    • Views: 221
    03-01-2018, 12:55 AM Go to last post
    • Replies: 0
    • Views: 311
    01-29-2018, 02:43 PM Go to last post
  8. Question Dynamic brake for HY01D523B (or similar Huanyang)

    Started by Foogl‎, 01-03-2012 11:29 PM
    • Replies: 5
    • Views: 3,334
    12-30-2017, 10:06 PM Go to last post
  9. Vfd spindle just stopped spinning.

    Started by potts43‎, 12-11-2017 07:04 AM
    4 Pages
    1 2 3 4
    • Replies: 40
    • Views: 932
    12-15-2017, 10:43 AM Go to last post
  10. Need Help!- vfd help over a year now please

    Started by transformer82‎, 12-03-2017 06:49 AM
    • Replies: 6
    • Views: 289
    12-03-2017, 12:36 PM Go to last post
  11. Need Help!- Running an Air Compressor with a VFD.

    Started by TheDeon‎, 10-23-2017 07:10 AM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 1,289
    10-30-2017, 08:25 AM Go to last post
  12. Problems with my Hitachi WJ200-022sf

    Started by Ewalk02‎, 10-22-2017 01:07 AM
    adjusting, hertz, run, spindle, vfd
    • Replies: 6
    • Views: 464
    10-22-2017, 11:30 PM Go to last post
  13. Huanyang HY04D043B advise required.

    Started by Sunderz‎, 10-16-2017 12:23 PM
    • Replies: 0
    • Views: 152
    10-16-2017, 12:23 PM Go to last post
  14. Correct VFD Wire Gauge

    Started by bkp08817‎, 08-30-2012 12:06 PM
    everyone, say
    • Replies: 9
    • Views: 5,223
    09-27-2017, 12:36 PM Go to last post
  15. Rotary phase coverter - 5hp - queries re capacitor sizes

    Started by Stewey‎, 05-18-2016 07:55 AM
    2 Pages
    1 2
    • Replies: 14
    • Views: 1,708
    09-26-2017, 03:02 PM Go to last post
  16. Need Help!- I need more power

    Started by Tafc7306‎, 09-21-2017 04:40 PM
    2.2 kw huanyang vfd, drill, problem, pump, rpm
    • Replies: 9
    • Views: 341
    09-21-2017, 11:20 PM Go to last post
  17. what converter do I need?

    Started by tom o‎, 08-24-2017 07:17 PM
    amp, converter, haas, posible, time
    • Replies: 4
    • Views: 505
    08-25-2017, 05:23 PM Go to last post
  18. Makino RMC55-A10 on AR RPC

    Started by ardentindustries‎, 08-25-2017 03:21 PM
    • Replies: 0
    • Views: 168
    08-25-2017, 03:21 PM Go to last post

Page 1 of 33 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (0 members & 7 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands