Phase Converters

Page 1 of 34 123411 ... LastLast
Threads 1 to 20 of 662

Forum: Phase Converters

Running 3 phase machines on single phase power discussion

  1. Question Need Help!- Phase converter for a machine with several load changes: rotary or digital?

    Started by Ale88‎, 10-20-2018 12:25 AM
    2 Pages
    1 2
    • Replies: 16
    • Views: 272
    10-21-2018, 03:11 PM Go to last post
  2. Huan Yang GT-5R5G-2

    Started by andyjack38‎, 10-12-2018 01:30 AM
    • Replies: 0
    • Views: 77
    10-12-2018, 01:30 AM Go to last post
  3. fine tuning my self built 10hp phase converter.

    Started by lin842‎, 06-22-2018 02:36 PM
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 65
    • Views: 1,765
    09-05-2018, 01:33 PM Go to last post
  4. Need Help!- Fuling DZB200M Programming mode

    Started by mutski‎, 01-30-2011 11:12 PM
    2 Pages
    1 2
    • Replies: 21
    • Views: 13,057
    07-24-2018, 08:57 AM Go to last post
  5. VFD setup for H.S.D 6.8kw spindle

    Started by IN-WondeR‎, 07-20-2018 10:23 AM
    2 Pages
    1 2
    cnc, drive, speed, unidrive, vfd
    • Replies: 12
    • Views: 465
    07-22-2018, 04:28 PM Go to last post
  6. Isacon Power Control Tech Co. -HY VFD (HY01D523B)

    Started by BigWilbur‎, 03-27-2018 01:08 PM
    • Replies: 3
    • Views: 504
    05-22-2018, 04:55 PM Go to last post
  7. Need help! Balance voltage rotary converter motor 7.5 hp

    Started by jfroux_1‎, 04-01-2018 04:09 PM
    5 Pages
    1 2 3 4 5
    • Replies: 53
    • Views: 1,625
    05-19-2018, 02:28 PM Go to last post
  8. Need Help!- powtran i9000 settings to control 3 phase motor speed

    Started by bluebumper‎, 04-14-2018 03:37 AM
    board, ess, input, speed, vfd
    • Replies: 10
    • Views: 380
    04-21-2018, 10:50 AM Go to last post
  9. Unhappy LCD panel does'nt display

    Started by bivegele‎, 04-21-2018 05:50 AM
    cnc, display, inverter, rpm, work
    • Replies: 0
    • Views: 204
    04-21-2018, 05:50 AM Go to last post
  10. Need Help!- New VFD and spindle motor, RPM too low

    Started by phootsman‎, 04-04-2018 07:47 PM
    • Replies: 9
    • Views: 358
    04-07-2018, 08:52 PM Go to last post
  11. 1 phase 230v to VFD 3 phase 230V?

    Started by dukei‎, 03-26-2018 02:54 PM
    • Replies: 7
    • Views: 422
    04-04-2018, 05:21 PM Go to last post
    • Replies: 10
    • Views: 5,331
    03-13-2018, 03:03 PM Go to last post
  12. Rotary 3-phase converter

    Started by chuck767‎, 02-28-2018 09:44 PM
    converter, motor, phase, rotary, start
    • Replies: 2
    • Views: 317
    03-01-2018, 01:55 AM Go to last post
    • Replies: 0
    • Views: 378
    01-29-2018, 03:43 PM Go to last post
  13. Question Dynamic brake for HY01D523B (or similar Huanyang)

    Started by Foogl‎, 01-04-2012 12:29 AM
    • Replies: 5
    • Views: 3,583
    12-30-2017, 11:06 PM Go to last post
  14. Vfd spindle just stopped spinning.

    Started by potts43‎, 12-11-2017 08:04 AM
    4 Pages
    1 2 3 4
    • Replies: 40
    • Views: 1,172
    12-15-2017, 11:43 AM Go to last post
  15. Need Help!- vfd help over a year now please

    Started by transformer82‎, 12-03-2017 07:49 AM
    • Replies: 6
    • Views: 363
    12-03-2017, 01:36 PM Go to last post
  16. Need Help!- Running an Air Compressor with a VFD.

    Started by TheDeon‎, 10-23-2017 08:10 AM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 1,561
    10-30-2017, 09:25 AM Go to last post
  17. Problems with my Hitachi WJ200-022sf

    Started by Ewalk02‎, 10-22-2017 02:07 AM
    adjusting, hertz, run, spindle, vfd
    • Replies: 6
    • Views: 614
    10-23-2017, 12:30 AM Go to last post
  18. Huanyang HY04D043B advise required.

    Started by Sunderz‎, 10-16-2017 01:23 PM
    • Replies: 0
    • Views: 207
    10-16-2017, 01:23 PM Go to last post

Page 1 of 34 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 9 users browsing this forum. (0 members & 9 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands